Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Thanks for supporting LPF!

Avery's Instagram

Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 1/10/16

Laserbeamk

Banned
Joined
Jul 29, 2015
Messages
256
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/16/15

I was wondering if you can make a host for me out of cobalt alloy with a copper heatsink and hold 2x 18350s. I would also add a diamond module to the diode. That will make it litterally in-destructible.
 



Ehgemus

New member
Joined
Feb 28, 2009
Messages
1,385
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/24/15

New host added today 8-24-15
 

Laserbeamk

Banned
Joined
Jul 29, 2015
Messages
256
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/24/15

I would like a beam expander
 

Alaskan

Well-known member
Joined
Jan 29, 2014
Messages
12,937
Points
113
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/24/15

If you can make one for me like the last one you just posted except for four 32650 batteries in series and as wide a head you can possibly make (over 3.5 inches, 4" is best) which has deep 1/4 inch wide heat sink fins .5 inch deep (minimum) with 1/4 inch spacing between the fins and a head width to length dimension of 1.5 to 1 (1.5 times longer than its width) with a high current on-off switch near the head in addition to the switch in the end cap and thread the head/heat sink to allow a large diameter pipe to screw on it later with no less than 1 inch of thread length, you will have sold another one to me.

It would need a place to put some drivers too (wide and long enough for several), but something more secure than the piece which just sits in there with glue, maybe a part of the head, if possible. Also, the power wire would need to be no less than 16 gauge, 14 better.

Also, last but not least, a long ledge in the front of it for a knife edge assembly which is 95 percent as wide as the head but 6 inches long and 1/2 inch thick milled as flat as possible on both sides. Here's a photo of something similar but much smaller:

711913bd-0791-4a0e-b03e-4a9248f77b93.jpg


There would be a hole in the center of the head made to allow mounting a 12mm aixiz module too, but not two diodes as in this photo. That hole would be used to run the wires through to the diodes in the knife edge, but the diameter of a aixiz module in case I want to mount one there someday.

The only dimension I need to give you which will make or break the unit from working for me is the height of the ledge for the knife edge in relation to the center of the head/aixiz module hole which I would need to provide before the work could start.
 
Last edited:

IsaacT

Well-known member
Joined
Aug 25, 2010
Messages
5,947
Points
83
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/24/15

Hey Ehgemus, been awhile since I have been on. Your hosts are looking better than ever, especially that one with the acrylic front piece, and I am glad to see those side switches in more and more models. Love the feel. Hope you are doing well!

Cheers
-Isaac
 

Ehgemus

New member
Joined
Feb 28, 2009
Messages
1,385
Points
0
Hey Ehgemus, been awhile since I have been on. Your hosts are looking better than ever, especially that one with the acrylic front piece, and I am glad to see those side switches in more and more models. Love the feel. Hope you are doing well!

Cheers
-Isaac
Thanks Isaac

Alaskan, get them dimensions of the head so we can start on this monster. Lol
 

TaterMay

New member
Joined
May 16, 2015
Messages
350
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/16/15

I was wondering if you can make a host for me out of cobalt alloy with a copper heatsink and hold 2x 18350s. I would also add a diamond module to the diode. That will make it litterally in-destructible.

Umm...what? Lol. A diamond module? Please do tell where you plan on getting a diamond module.
 

Alaskan

Well-known member
Joined
Jan 29, 2014
Messages
12,937
Points
113
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/24/15

Thanks Isaac

Alaskan, get them dimensions of the head so we can start on this monster. Lol

That would be so awesomely cool, I have all the parts to build the optics for this baby as soon as you have the time to make the platform host for me :)

The distance the shelf needs to be from the center of the head is exactly 9mm.
 

Laserbeamk

Banned
Joined
Jul 29, 2015
Messages
256
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/16/15

Umm...what? Lol. A diamond module? Please do tell where you plan on getting a diamond module.

It's impossible but nice to have one if your rich and you want to sink in some real heat.
 
Last edited:

gozert

Well-known member
Joined
Nov 18, 2014
Messages
1,087
Points
63
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/16/15

It's impossible but nice to have one if your rich and you want to sink in some real heat.

So you're asking him if he can make something that you already know of is impossible?


zioGXeh.jpg
 

Laserbeamk

Banned
Joined
Jul 29, 2015
Messages
256
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/16/15

So you're asking him if he can make something that you already know of is impossible?


zioGXeh.jpg

I didn't say it was completely impossible still possible if you got the money.
There are tons of diamonds in this world, but just not cheap.
 

Ehgemus

New member
Joined
Feb 28, 2009
Messages
1,385
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/24/15

Bump^^
 

robomont

Member
Joined
Mar 7, 2013
Messages
195
Points
18
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 8/24/15

love the design of that first side clickie.lots of beautiful work.
 

Ehgemus

New member
Joined
Feb 28, 2009
Messages
1,385
Points
0
Re: Fs: CUSTOM LASER HOSTS, NEW HOSTS ADDED TODAY 9/2/15

New host added today. Better check this one out. ^^
 




Top