Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Dose anybody see anything wrong with this wiring ?

Accutronitis

Accutronitis

0
Joined
Dec 30, 2016
Messages
1,409
Points
0
The laser is a 1.3 watt 445nm blue laser using a X-drive V6 1100mA Fixed that does not have a constant ground and the diode in not isolated, the new x-drive should be here today and I just wanted to be as confident as possible that I'm wiring it correctly.....

(it says flexdrive but it's a x-drive)



If there are no objections I'm going with this wiring ?
 
Last edited:





What's this, your fifth or sixth thread on the same laser with the same related issue/questions?

For the last time, please keep this all in the one thread. It makes everyone's life easier.
 
diachi said:
What's this, your fifth or sixth thread on the same laser with the same related issue/questions?

For the last time, please keep this all in the one thread. It makes everyone's life easier.
Click to expand...
BUT I have yet to get the answers I'm looking for and I'm running out of time !

Please don't throw "for the last time" at me because I am just trying to get the answers I need !
 
Last edited:
Accutronitis said:
BUT I have yet to get the answers I'm looking for and I'm running out of time !

Please don't throw "for the last time" at me because I am just trying to get the answers I need !
Click to expand...


Spreading all of the information across 5 threads just makes it harder for anyone to provide you answers. Not to mention there's lots of build/teardown/repair threads that would already answer your questions.

That wiring looks fine to me as long as there is electrical contact between the LD and the rest of the case.

If that driver has common ground on input and output you can simplify further and just tie the case pin of the LD to the cathode pin of the LD. Someone else that's used one of those drivers can confirm that, I've never used them.
 
diachi said:
Spreading all of the information across 5 threads just makes it harder for anyone to provide you answers. Not to mention there's lots of build/teardown/repair threads that would already answer your questions.

That wiring looks fine to me as long as there is electrical contact between the LD and the rest of the case.

If that driver has common ground on input and output you can simplify further and just tie the case pin of the LD to the cathode pin of the LD. Someone else that's used one of those drivers can confirm that, I've never used them.
Click to expand...

All I'm trying to do is get as many members as possible to see the questions I have because MANY times different members like to spend most of their time in one forum or another and the right member that could help me with ALL my questions may never see my one thread !

Not to mention there's lots of build/teardown/repair threads that would already answer your questions.
Click to expand...

And I have looked through a ton of them since Friday and I didn't find what I was looking for so what's a man to do ?

That wiring looks fine to me as long as there is electrical contact between the LD and the rest of the case.
Click to expand...
Yes it does.

If that driver has common ground on input and output you can simplify further and just tie the case pin of the LD to the cathode pin of the LD. Someone else that's used one of those drivers can confirm that, I've never used them.
Click to expand...
I don't know if it has a "common ground" but I can tell you that it does not have a "constant ground" ?
 
Last edited:
Accutronitis said:
The laser is a 1.3 watt 445nm blue laser using a X-drive V6 1100mA Fixed that does not have a constant ground and the diode in not isolated, the new x-drive should be here today and I just wanted to be as confident as possible that I'm wiring it correctly.....

(it says flexdrive but it's a x-drive)



If there are no objections I'm going with this wiring ?
Click to expand...

Your circuit is not a complete circuit. There is no path from the cathode of the battery to the cathode of the driver...
 
HydroSean said:
Your circuit is not a complete circuit. There is no path from the cathode of the battery to the cathode of the driver...
Click to expand...
The diode case is grounded to the host case, the diagram I borrowed doesn't depict that......

This diagram corrects any issues.........

 
Last edited:
HydroSean said:
There is no path from the cathode of the battery to the cathode of the driver...
Click to expand...


Yes there is, the case of the diode will be in contact with the host which is in contact with the cathode of the battery. The case pin of the LD will be connected to the -V connection on the driver (or the LD- if -V and LD- are shared.)
 
Accutronitis said:
The diode case is grounded to the host case, the diagram I borrowed doesn't depict that......
Click to expand...

Now you just have to ask yourself if there is a case pin and if there is, then is it isolated from the case of the diode? Note if its case positive or negative.
 
Last edited:
HydroSean said:
Now you just have to ask yourself if there is a case pin and if there is, then is it isolated from the case of the diode? Note if its case positive or negative.
Click to expand...
The diode case pin is fused to the diode case, Also I've been told the most all 445nm diodes are case neutral.....
 
Last edited:
diachi said:
Yes there is, the case of the diode will be in contact with the host which is in contact with the cathode of the battery. The case pin of the LD will be connected to the -V connection on the driver (or the LD- if -V and LD- are shared.)
Click to expand...

Oh then yeah it should work, but why not just cut off the case pin and solder the to the Driver- to the host?

Accutronitis said:
The diode case is grounded to the host case, the diagram I borrowed doesn't depict that......

This diagram corrects any issues.........

Click to expand...

Always put the switch between the battery and the driver. Do not put the switch at the battery cathode
 
Last edited:
HydroSean said:
Oh then yeah it should work, but why not just cut off the case pin and solder the LD- to the Driver-?
Click to expand...
it is on the driver output but I've read that drivers that do not have a "constant ground" must have a jumper wire from the host case to the input of the driver and the easiest way to do that is using the case grounded diode's case lead and a jumper wire to the driver power input side neg.....
 
Accutronitis said:
it is on the driver output but I've read that drivers that do not have a "constant ground" must have a jumper wire from the host case to the input of the driver and the easiest way to do that is using the case grounded diode's case lead and a jumper wire to the driver power input side neg.....
Click to expand...

Looks to me like it will work, just move the switch between the battery and the driver.
 
That is what case pin tends to imply. The very important question that was asked of you was whether the diode sources it's positive or negative from it's case like many of these do.

Also, making multiple threads on the same thing is very frowned upon here or anywhere.
Most people scroll to the bottom to see "latest posts" not only to their favorite section of the forums.

Lastly I am going to suggest putting terms like "how to build a laser" into that magic Google bar at the bottom of any page. All of these questions have been answered many times and if people are not competent enough to find such basic info, I personally don't want them within a few miles of me with a laser.
 
You must log in or register to reply here.





Back
Top