Hello,
today I had bad luck again with a 500 mA buck/boost driver. It was not from DTR!
I connected the new driver to my dummy load of 6 diodes and a 0,1 Ohm resistor. Nothing happens, no curent draw from my laboratory power device.
After checking the wiring, the same result. Is it possible to...
Hello,
since I started to join this forum, I built some custom made and/or modded flashlight laseerpointers with different colours and laser power.
1. 405 nm 500 mW
2. 450 nm 1,2W; 1,7 W: 7W+
3. 465 nm; 1,8 W
4. 488 nm; 150 mW
5. 505 nm; 150 mW
6. 520 nm; 800 mW
7. 635 nm; 200 mW and 700 mW...
Hello,
today I got two sharp laser diodes
Sharp GH0631IA2G 185mW 638nm Laser Diode
from DTR.
I pressed one into a 12 mm Copper heatsink from DTR and connected it to a brand new 500 mW driver from X-wossee.
Nothing happened! No current, no laser light. After that, I connected the diode...
Hello,
I made complete DIY Hosts for my first power lasers. Then i started to use flashlicht hosts. I think the ultrafire 501B hosts are nice. For medium power laser the convoy S2 is fine. Now I am looking for other possible hosts with 18650 batteries. I am also looking for better quality...
Hello,
because I hate to cut connections to measure the current to a laser diode, I bought a cheap clamp multimeter.
Attached you will see a picture with a comparison between the clamp meter and the power supply. If you set the multimeter to zero before, the results are nice, even at low...
Hello,
as I learned, most of the 465 nm power diodes have a ball lense. Some make a tight spot, some not. Decapping the diodes will decrease the lifetime of the diodes.
Is it possible to use a second lense in front of the ball lense to improve divergence?
I can make the special heat sink by...
Hello,
I searched this forum for a laser Diode comparison list, but could not find one.
There are some compact information at the DTR shop, also a lot of information hidden in numerous threads. I would like to see a compact comparison list with information like : mono/(multimode; wavelength...
Hello, I ordered 505 nm diodes from Techhood. Does anyone of you have experience with this wavelength?
I also ordered a new sharp 490 nm Diode, because I killed mine with the wrong Driver. A little turn of the potentiometer of the big Driver gives the Diode approx. 1000 mA for the split of a...
Hallo,
some month ago, I bought this nice blue laser module:
https://www.ebay.de/itm/Focusable-465-470nm-3500mW-Blue-Laser-Module-Analogue-Modulation-For-Laser-Light/262580156386?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
Now I would like to build a laserpointer from this...
Hello,
looking for DIY laser parts, I see, that there are a lot of differént lenses for different wavelengths.
Do I need a special lense for every different wavelength?
What will happen, if I use a "red lense" for a 450 nm Diode? Is there only a bad focus, or will it destroy the Diode by...
Hello,
I finished my first copper heatsink for a 5,6 mm laser Diode. I drilled a 5,5 mm hole, followed by a light cut in my lathe.
With the digital caliper, i measured a Diameter of aprox. 5,60 mm.
I had luck, that i got a pressfit of my Diode in this heatsink.
My question is, how much is the...
Hello,
I am quite new with the laser and laserpointer Hobby. Until now, I have only a few low cost laserpointers from China,a nice 860 mw green Laser 8520 nm) and a 488 nm Laser with 3,5 W Output. At the Moment, i plan to build a 7W blue laser (450 nm) for engraving and a 2 W 450 nm...