Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers



Search results

  1. X

    FEELER: Custom WL e2 RGB Set [PICS]

    Bump! Price is now set reasonably! :P
  2. X

    Looking to buy Older Wicked Lasers

    I have 3 WL e2's with custom internals. R, G, and B! Let me know...
  3. X

    FEELER: Custom WL e2 RGB Set [PICS]

    Re: FEELER: Custom WL e2 RGB Set [PIC HEAVY] Thank you for the tip, updated the post!
  4. X

    FEELER: Custom WL e2 RGB Set [PICS]

    Hey folks, Long time no talk. I am thinking of selling my set of custom WL e2 builds. I am finishing up my degree and need to pay off debt to the school. I want these to go to a good and caring owner. Rare set of rare builds in rare hosts! All these are in very very good condition. I have a...
  5. X

    Wanted: WL e2 (A.K.A. Evolution Pro) even if it's dead...anyone?

    Hey guys, Looking to transform another e2/evo pro into a 445...anyone that has one let me know by posting here or PM'ing me! Thanks in advance, xXDUNNXx
  6. X

    Need to borrow! Anyone with an LPM! or anyone in MA???

    Hey guys, My car keeps giving me more and more problems. I recently finished a modded WL e2 445nm build that should be pumping out 1.3W ish and I am thinking of selling it. I really did not want to sell this. Although in order to sell it at the price it deserves, I need to confirm the power...
  7. X

    Help! What is causing this issue! Flexdrive set up at 1450ma...Tail current is 770mA?

    Figured it out...I knocked off the pot setting luckily I marked it so I set it right back to where it was :)
  8. X

    WTB: Cheap calibrated LPM! (and some new 445 safety glasses)

    Hey guys, I'm looking into a cheap <$50 LPM that is calibrated to test out my 445 build. Anyone? The laser is more than 1W but less than 1.5W. I know this much.
  9. X

    Help! What is causing this issue! Flexdrive set up at 1450ma...Tail current is 770mA?

    Would added resistance to the case cause this? I ask because the mosfet does add some resistance. Also, IMR's are on the way...
  10. X

    Help! What is causing this issue! Flexdrive set up at 1450ma...Tail current is 770mA?

    Well...at 3.7V more like 3A with 80% efficiency. I was not thinking correctly about the driver when I posted that. Flaminpyro set it so I assume yes on the test load lol...I trust him. And yes, he cut me a custom hs for between the driver and aixiz which is pressed into the host. The m140 when...
  11. X

    Help! What is causing this issue! Flexdrive set up at 1450ma...Tail current is 770mA?

    So I built another 445nm in an e2 host...the circuit goes like so V+, flexdrive @ 1450mA, LD+ V+, Tact Switch, MOSFET Gate LD-, MOSFET Drain, Case MOSFET Source, Case MOSFET Gate, 10K resistor, MOSFET Source NOTE that Flexdrive is set at 1450mA and the resistance while on of the...
  12. X

    TIP120 MOSFET to power a high current build with a low current switch????

    Well, I meant since the ground is continuous, flexdrive to transistor to casepin/neg ld pin. Anyone know if that transistor I meantioned will work judging by the specs?
  13. X

    TIP120 MOSFET to power a high current build with a low current switch????

    Wait...if a mosfet will always have current running through it...doesn't that mean that if it sits off for a while, it will drain the battery? EDIT: http://www.nteinc.com/specs/2900to2999/pdf/nte2981.pdf would that work?^^^
  14. X

    TIP120 MOSFET to power a high current build with a low current switch????

    Got it! now p vs n type MOSFET...n type to switch ground AFTER the flexdrive and p type to switch the power BEFORE the flexdrive... Which is a better idea...switching the flexdrives input voltage...right?
  15. X

    TIP120 MOSFET to power a high current build with a low current switch????

    That is half the battle! Thank you...now how do I tell what current will run through the switch that needs to be limited at ~50mA? It would be [ V+ to switch, base ] [ V+ to collector ] [ Emitter/Drain to V+ of the flexdrive ] Right? Case will be negative.
  16. X

    TIP120 MOSFET to power a high current build with a low current switch????

    Lol guys...thanks for the pointers...I have done quite some research. I want to know what specs of the transistors do what...I figured someone on here may have some better descriptions that are less technical than the ones found online. I need this to be an on/off switch, that is all...the least...
  17. X

    TIP120 MOSFET to power a high current build with a low current switch????

    How do I do this! I have google'd and done so much research. I am doing a high power 445 build with a micro flexdrive in a WL e2 and it will be pulling 3A at one point. I cant have 3A going through a 50mA rated switch!!! I've come to the conclusion that a MOSFET will do the trick...but how do I...




Top