Search results

updated with video in the first post but here is a link anyways... Mag laser - YouTube

From this point forward I am not responding to ANY post unless it is directly dealing with this sale. This thread has been mucked up enough as it is. If you have an issue you need to take up with me other than dealing with this laser you know where the PM button is.

I am sorry if you thought that was directed at you. It was not at all.

Jesus Christ I think this has been covered. WHat else do you want here? I took pictures of the build have shown proof of its power and am going to show it in video. Personal opinions of me aside I guarantee that I do damn good work and I will guarantee that.

Dont worry I am going to re meter it on film this evening. How far do you think I need to zoom out so everyone can be sure that I am not pointing a "second" or "third" laser at the sensor to pad my numbers?

I was just about to retort, with my own screen shot supporting my end. I can prove some things as well but you are right this is pointless. I am ok with the edit at this point as my initial rage has come and gone.

After tonight we will discuss this.

SO, to put this to bed I am going to go ahead and meter this one more time. It will be this evening (2/13/12). I am leaving for work now so if there are any request on how I should perform this test so that I can satisfy any potential buyers please speak up. I am going to follow the lasrbee...

That sounds good I need to see what it is going to cost to ship to you. Can you send a PM with your address. I may be only able to cover some of the shipping if it starts to get outrageous. Also I do accept PayPal.

I did reply :yh: I do not think it is a secret that running these diodes @ 1.8a is pushing them pretty good. I would like to keep the runtime as low as possible for the new owner. However, I will run it for a 1.5 minute run IF it is a request from several potential buyers. As of right now...

Thanks for the support guys. One thing I will mention is that I had the beam so unfocussed on the thermopile that small pieces of it were hanging off either side even when centered. I have no doubt that this will meter over 2.6 if I were to focus it a bit more but I am scared that I am gong to...

I would not blame him if he didn't. Either way find a way to get it done yourself. Too easy to get burned.

Ok, here is the video fresh as of a few minutes ago. Laser is reading right over 2500mw and staying strong. 95MUy2IyCNw&hd http://www.youtube.com/watch?v=95MUy2IyCNw&hd=1&t=1s I just finished a build that I would like to sell. here are the specs... The host is a 2c sized mag that has been...

Yes DTR m140 diode and g2 lens, jib 1.8a driver.

Well i ordered 2 of these with the g2 lens about 2 months ago and I just got the first of the two running tonight. My brand new laserbee II metered it @ 2419mw........:eg:

I went ahead and pressed it out and added thermal compound. Good thing too because I suspect that thing is getting HOT. It metered @ 2419mw tonight.

Once again you guys know your stuff. The 15/32 bit was perfect. I had to gently press it into the sink and it is definitely tight enough that I do not have to add any type of holding device or compound. Best part is the bit was free, my job rocks!

I have a sink for a 445 module that needs a hole in the center of it so that I can press the module into it. What size bit are you guys using to get this done? The module mesures 11.90mm or .4685" neither of which are standard sizes.... So help a guy out here.... Are you using a drill press or...

So these are run in series with each other? Any real advantage to them over the jib?

When people say that their 445 build is powered by dual flex drives does that mean that their are actually 2 drivers? I want to push my 445 diodes to about 1.8a Right now I have a 1.8a Jib driver that I bought from Moh a while back. If I wanted to look into these flex drives, where are they...