Search results

we wont be very lucky once the value of the dollar goes to crap from all money we owe to china and other countries :yabbem:

Im assuming thay are pulled from a larger device that was scraped so wavelength and power are unkown.. It would be pure luck if it was 808nm, Im gessing it will be a higher nm. Good for learning or burning paper :rolleyes:

May or may not be a deal.. COHERENT LASER DIODE POWER BAR (See Photos) - eBay (item 390247168193 end time Oct-08-10 11:18:10 PDT) No wavelength or power listed, or a good pic of the die. but it is listed as being made buy coherent. I think this seller has sold used diode bars in the past and...

Im not a experienced machinists. But ive ben useing this tool I made from the crap HF bits I had, with decent results. I still reface the piece I cut off, but it beats numb hand's from a sawzall.

Most excellent! I was hoping you would say over 200ma. I had ben debateing on adding a button to a old driver, or geting the new driver for a 6x pen buld. I'm geting the new one now. Thank you :D

Thank you for the review, and sharing the corect way to power it! Have you check to see if it will put out 250ma? The reason I ask, the old drivers where said to be 50-200ma. But only put out around 180ma and thay also had the finicky pot so it was hard to get the ma you where after. These new...

I second the request for a 18650 host. Would be nice for a 445nm diode and Drlava's optics.

Hey all I have a 3.2v non protected battery that was discharged way to far and sat for a long time. It is now only at .51v :eek: and my charger whont charge it or evin seem to recognise that the battery is there. I did a quick seached around and could not find a fix, so I thought I would share...

Thay are the 405-G-2 lens, Jay gets his from the manufacture I think. I Have a used these modules before, both the red and blue lens one's. EDIT: just noticed this was in the 445 section, I havent used these with a 445nm diode. The red lens one has the same power output as Aixiz glass for...

To ezzy :na: I go cross eyed when its in the right order, makes it ezzy.

Re: Can´t run Half Life 2 on Windows 7 Are you trying to run the game for the first time?, did you just upgrade to win 7? Have you got the latest DirectX / Vid drivers / .Net frameworks ect.?

Yup thats my work, ive got a tap from Victor on the way. Ben looking for one with the correct thread count for a while, tell Lary posted where to get one.:san: I had done it before I found where to get a proper tap. Also I had a defective Aixiz that was not fully machined for a diode to fit, so...

You will lose the back half no doubt. Id say you can take a Aixiz module down to just under 10mm only if ya have the skill's, thay are hard to center or mill straght (cuzz thay are small and short) But it is verry possible down to just under 10mm depending on your patience, you might mess up one...

Re: ►AMK GB◄ ~ SF-AW210 Diodes $10 Each LOL That got me laffing good enuf to make me get a side cramp:crackup::crackup::crackup:

Re: ►AMK GB◄ ~ SF-AW210 Diodes $10 Each I got a box today :wave: Most sleds had light damage and optic's where intact.:yh: Some sleds had damage to the opitc's but looks like the cubes are fine, so all is good there. But i had one with sever damage and a missing red diode.:(...

Re: *445nm lasers* !arrays 550$ and diodes 35$! I would like 2 diodes please :yh: EDIT: Payment sent.

I think FAC is very small just bigger than the die that emits the light in the diode.. So you would have to dee can the diode, wich is not ezzy. do a shearch for IR diodes with a FAC. From a post at PL, "The FAC is a very thin (200um or so) piece of glass fiber in the long axis of the emitter...

Current= 900ma Power = 980mw Lens = Aixiz 445 Glass Driver = LM317 Host = DIY TEC Labby Power Source = 15v 10A DC power supply Operating Time = 3~4 hours Source= I think AJ-X130 it came from EF's GB 2 or 3. Hears a pic of my contraption if any one is interested to see it.

Re: Goggles for 445nm Just so it's clear, I still do not condone the use of these glasses over 300mW! If thay melt at half the power we whant to run these dioide's at, its not safe! (IMHO):yabbem: I am geting the certified glasses and suggest that any one geting these diode's do the same...

No you would need a boost driver. The rkcstr driver needs atlest 7v with blue-ray, this host will hold one 14500 3.7v(AA size) or two CR2 3v batteries. You can get a boost driver that sould work grate for a PHR (if you can solder a SMD resistor) from this same site. I got myself two of the boost...