Old 03-02-2011, 09:17 PM #49
BShanahan14rulz's Avatar
Class 3B Laser
 
Join Date: Dec 2009
Posts: 3,175
Rep Power: 3651
BShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond repute
BShanahan14rulz BShanahan14rulz is offline
Class 3B Laser
BShanahan14rulz's Avatar
 
Join Date: Dec 2009
Posts: 3,175
Rep Power: 3651
BShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond reputeBShanahan14rulz has a reputation beyond repute
Default Re: Single 10440 RED LOC build

Would like to clarify: when manufacturer of a battery says 700mA max discharge, that doesn't mean that the cell can only discharge 700mA max. That means that the manufacturer recommends that you only attempt to draw no more than 700mA from the cell.

As you were...

Also, I've been testing LOCs with a single amc7135. I've blown a LOC, but too many variables to assume that it was the amc7135 at fault, because I needed it that day, so ended up "slip-streaming" a single 7135 chip between the + and - wires inside the back end of the aixiz module and using magnets as the power connections. Hopefully be able to find a scope to scope the output of the 7135



Last edited by BShanahan14rulz; 03-02-2011 at 10:04 PM.
BShanahan14rulz is offline   Reply With Quote


















Old 03-03-2011, 01:57 AM #50
Leodahsan's Avatar
Class 3R Laser
 
Join Date: Aug 2010
Location: Rio Grande do Sul, Brazil
Posts: 2,088
Rep Power: 165
Leodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond repute
Leodahsan Leodahsan is offline
Class 3R Laser
Leodahsan's Avatar
 
Join Date: Aug 2010
Location: Rio Grande do Sul, Brazil
Posts: 2,088
Rep Power: 165
Leodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond reputeLeodahsan has a reputation beyond repute
Default Re: Single 10440 RED LOC build

Thanks. The batteries were tested (by DX forum members) that the maximum discharge is 900mA. But they vary a lot so I don't trust they..

I've thinked about the AMC, but they don't sell it here in Brazil and it takes A LOT of time to reach from china or other countries..

thanks.
__________________
Any doubts, feel free to PM ou send me a visitor message! I'll help as I can.

Best regards,
Leonardo
__________________

* Deploying CNC router project soon...

DONATE!
The smallest donation will help, if you like this enormous information resource, just do it.
Leodahsan is offline   Reply With Quote
Reply

Tags
10440, 660nm, aaa, red, single





Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

























Privacy Policy | Advertising Disclaimer | Terms of Use


 


All times are GMT. The time now is 03:42 PM.


Powered by: vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO
Privacy Policy | Advertising Disclaimer | Terms of Use
Copyright (C) 2017 Laser Pointer Forums, LLC