Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

newbie: 3v, 3.6v? fried one already.

S

sync

0
Joined
Dec 9, 2010
Messages
6
Points
0
I wanted a phaser ever since I first saw then on the original Star Trek when I was five. Recently I had the brain storm to put a green pointer diode into an old phaser model, thought it was an original idea, went on the internet, found you wonderful folks had been doing it for some time. Went ahead and build my toy with a 200mw green driver and diode running on a 3v battery. It was great until I had the bright idea of building a better, higher voltage battery pack. The package said 3.6 to 4.2 volts. I figured it had a 5v resistor so….. . The new unit is now on its way, and I want to get the most out of it without frying the driver. So, for us low to no tech newbies; what battery voltage, 3, 3.6, or other, should I use? Thanks. Feel myself becoming slowly obsessed with pretty green light……

Thanks
 





Leodahsan

Leodahsan

0
Joined
Aug 7, 2010
Messages
2,086
Points
0
Welcome to LPF ! :D
you should introduce yourself in the appropriate thread first.

I didn't understand your question very well, but, it seems you want to use a higher voltage on your green laser phaser. It is not very easy to guess unless we know what you are using. :)
 
Kevlar

Kevlar

0
Joined
Apr 26, 2010
Messages
1,353
Points
48
sync said:
I wanted a phaser ever since I first saw then on the original Star Trek when I was five. Recently I had the brain storm to put a green pointer diode into an old phaser model, thought it was an original idea, went on the internet, found you wonderful folks had been doing it for some time. Went ahead and build my toy with a 200mw green driver and diode running on a 3v battery. It was great until I had the bright idea of building a better, higher voltage battery pack. The package said 3.6 to 4.2 volts. I figured it had a 5v resistor so….. . The new unit is now on its way, and I want to get the most out of it without frying the driver. So, for us low to no tech newbies; what battery voltage, 3, 3.6, or other, should I use? Thanks. Feel myself becoming slowly obsessed with pretty green light……

Thanks
Click to expand...

Why did you build a "better, higher" voltage battery pack? Usually green modules only require ~3V.

You should use the battery voltage that your green laser requires, it should say in the documentation what voltage to use. Do you have a link for the green laser you have?
 
S

sync

0
Joined
Dec 9, 2010
Messages
6
Points
0
I have the basics I need figgured out from reading this site and doing a little more research. The driver-diode had no documentation, just some 200 mw green pointer-driver knock-off. CR 123 battery worked fine, and it's an easy fit in the phaser. I just wanted as bright a laser as I could fit in the model and thougt a little more voltage would make it brighter. Over-all, the phaser worked fine, and I'm still waiting for the replacement. Thanks.
 
Coherent Light

Coherent Light

0
Joined
Jul 17, 2010
Messages
2,160
Points
0
Driver will covert the extra voltage to heat until it finally burns out. The Laser will not increase in brightness by increasing the voltage once you reach the correct operating range.
 
JLSE

JLSE

1
Joined
Dec 13, 2007
Messages
3,580
Points
0
Most green drivers will allow more mA to the diode by increasing the
input voltage. Changing out a 3v power supply to a 3.6v will give an
undetermined increase (test before and after) but may not benefit.

What you are doing is essentially a pot mod without the accuracy.

You'd be better off leaving it 3v and turning up the pot a touch. Monitor
the current as you do this and the brightness of the beam as well.
If you have an LPM, even better....

By simply increasing the mA with a higher voltage, you can burn the LD
and quite possibly the driver. With a pot mod you still risk the diode
but will have some control over things..
 
You must log in or register to reply here.




Top