Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

water resistant arctic?

thedekker

thedekker

0
Joined
Aug 24, 2010
Messages
11
Points
0
If nobody wants to try this, by all means that is OK. I am just curious.
I heard the Spyder 3 series of lasers by WL are water resistant. Anyone test this?
Also curious what a blue laser would look like under water. Water absorbs light, red goes first I believe, so I'm wondering what type of distance you would get on a beam underwater. of course, that is also subject to how clean the water is etc.

Maybe I'll try it with mine when it shows up...could also be extremely blinding, I would expect in murkier water the light would scatter everywhere along the beam...or something. i'm no expert here.

Eventually, we're going to need freaken sharks with freaken laser beams attached to their heads..

thoughts?
 





Tech_Junkie

Tech_Junkie

0
Joined
Jan 2, 2009
Messages
11,800
Points
0
The laser body is water resistant, the tail cap isn't. Typical BS fro WL as usual.

And water resistant is not waterproof.
 
Prototype

Prototype

0
Joined
Jun 19, 2009
Messages
2,710
Points
0
By water resistant they mean it can withstand being splashed with water, not total submersion. The tailcap has a 'safety' pin interlock that would leak and there are no o-rings as far as I know.
 
Ash

Ash

0
Joined
Mar 3, 2009
Messages
1,981
Points
0
Yes. The original Spyder III hosts were completely waterproof.

@ ~40 seconds you see three Spyder III lasers (2 532nm and 1 473nm) in water.

The G1 Arctic is not waterproof (completely) because the safety interlock in the tail cap is not sealed. The G2 versions are less waterproof than the G1's because (I think) the smart-switch does not have a water-tight seal. :cool:
 
Last edited:
thedekker

thedekker

0
Joined
Aug 24, 2010
Messages
11
Points
0
Ahh very nice thanks Ash. chicks with lasers...awesome!
would still like to see some long distance beam under water. guess I'll have to waterproof it myself. how hard can it be?
 
Prototype

Prototype

0
Joined
Jun 19, 2009
Messages
2,710
Points
0
Ash said:
Yes. The original Spyder III hosts were completely waterproof.

@ ~40 seconds you see three Spyder III lasers (2 532nm and 1 473nm) in water.

The G1 Arctic is not waterproof (completely) because the safety interlock in the tail cap is not sealed. The G2 versions are less waterproof than the G1's because (I think) the smart-switch does not have a water-tight seal. :cool:
Click to expand...


Those are Spyder I lasers...that video was uploaded in October of 2007, long before the Spyder III existed...
 
Tech_Junkie

Tech_Junkie

0
Joined
Jan 2, 2009
Messages
11,800
Points
0
thedekker said:
how hard can it be?
Click to expand...

Very hard. You'd have to dismantle the whole laser. Even if you didnt screw it up, you'd have to fit O-rings, and that alone is hard. You'd have to cut a channel for it to sit in.

I would not waste my time or money.
 
F

Foxer

0
Joined
Aug 31, 2010
Messages
42
Points
0
Even if one of my lasers was completely waterproof I don't think i'd ever want to submerge it in water.....
 
Tech_Junkie

Tech_Junkie

0
Joined
Jan 2, 2009
Messages
11,800
Points
0
I'm sure the thrill would wear thin really fast.

Only if your Arctic dies would I chance dismantling it, and waterproofing it. It can be done, but its not a novice/intermediate level project.
 
jeffreythe00

jeffreythe00

0
Joined
Jan 13, 2010
Messages
2,516
Points
63
You will need o-rings on both the front cap and the tailcap. you will also need to figure out a way to waterproof the safety key. those are the main parts. I would also reccomend gutting your Arctic if you can because I would not want to risk 200$ of components if I didn't have to. I'm not sure what kind of handyman skills you got but it should be both fun and interesting.
 
F

Foxer

0
Joined
Aug 31, 2010
Messages
42
Points
0
LOL...

Just from my experience.... made in China electronics and water don't mix. ;-P

Neat videos btw...
 
thedekker

thedekker

0
Joined
Aug 24, 2010
Messages
11
Points
0
Tech_Junkie said:
Very hard. You'd have to dismantle the whole laser. Even if you didnt screw it up, you'd have to fit O-rings, and that alone is hard. You'd have to cut a channel for it to sit in.

I would not waste my time or money.
Click to expand...

good point. Luckily however, I own an auto shop, and have a parts department filled with O-Rings. It would be a waste of time, not money haha.

then again theres the possibility of me screwing something up in the process of dismantling it, and voiding warranty. thats where the waste of money comes in I guess.
 
oic0

oic0

0
Joined
Jun 15, 2010
Messages
289
Points
0
Another issue is the lenses. Every time it gets wet its going to need cleaning afterwards if you want it to be 100%. I dont know about you but it sounds like a big hassle to me.
 
You must log in or register to reply here.




Top