GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

JETLASERS · May 28, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

Sparkys said:
Well -- Well ..

In watching Smeerworst's video -- I see my Laser operates differently than his.

Thanks much for your feedback -let's check them one by one.

Upon arming the Laser -- His has 3 Green lights next to his momentary switch. I also have these same 3 lights but -- Mine are always RED. To be clear -- Once mine is armed my lights are RED. Then depressing either the momentary switch or depressing the on button -- Then the top 2 lights turn a purple - Top one is the brightest and the bottom one doesn't change.

Yes, some led indicator are red, some are green - we first used the green mini leds for the green but some customers said the indicator is too weak, so we changed it to red which are more visible. But green is also okay.

Three led indicators are all on when the general switch(tail switch) is on and when you depress the momentary button, only the first two leds turn blue - it tells the upper button(momentary button) is working.

He has a jack plug - As well as mine. When he removes his and arms the Laser nothing happens when one depresses the momentary button or the on button. On mine -- I don't need a jack plug. Just arm and she's ready to light when either button is pushed next to the 3 RED lights. To be clear -- On mine -- either with or without the jack plug I simply arm by pushing the arming button next to the jack plug -- The 3 RED lights come on and I simply push one of the 2 buttons and She lights up. I also received a short curly cord with a stereo plug on one end and a weather proof switch on the other end. Inserting this into the female jackplug in the tail cap does nothing. I push the switch several times either armed or not and the 3 lights don't light up. For my purpose I don't need this remote switch.

I get it. Your jack plug was disabled - to make it work, it takes a bit mods on the circuit inside the tailcap. The remote switch works the same way as the jack plug. If you wanna it to be enabled, i can get you a new tailcap - it solves the problem and makes both the jack plug and the curly cord plug(mousetail switch) work - then without them plugged, the laser will not be switched on whatsoever.

Just use these examples of what seems like issues and thoroughly test before shipment so every customer is Happy with their purchase.
Until I saw this video I wasn't going to post my minor issues - But .. To make the product better I decided to make this post -- Thank You.
Dave

Thanks Dave for every feedback - very helpful - anyway let me know if you wanna make a change on the tailcap.

Sparkys · May 28, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

Hi Gray --

Wow -- Fast response .. .. .. Don't you ever SLEEP ?? ??

I'm one Happy Camper -- Even though mine isn't quite right .. .. It works GREAT for my purpose !! !!

Take Care and :thanks: for all your H E L P .. ..

Now -- It's my Bed Time .. .. :wave:

JETLASERS · May 28, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

Sparkys said:
Hi Gray --

Wow -- Fast response .. .. .. Don't you ever SLEEP ?? ??

I'm one Happy Camper -- Even though mine isn't quite right .. .. It works GREAT for my purpose !! !!

Take Care and :thanks: for all your H E L P .. ..

Now -- It's my Bed Time .. .. :wave:

Thanks - yep i sleep EVERY night!! - in GMT+8 China time。 Have a good night! :wave:

hakzaw1 · May 28, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

KapHn8d said:
Gray,
I'm not sure if the purchase window is still open on this group buy, but I just sent you an email requesting info.
Thanks,
Clayton

Ok I am here-- I can help you.

this GB has no end date ATM- hak

_ to lonepine-
PM coming- stay up a bit longer-

LtKernelPanic · May 29, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

Hmm. If these prices are going to be good past May 31st getting one of the 473nm listed in the OP is almost a certainty.

I do have a couple quick questions for either Gray or Hak. I see the 473nm in the PL-E Pro can use either 18650 or 26650 batteries but I assume given the choice a 26650 would be the better option. I have to order a bunch of batteries for other lasers/lights anyways so is there a reason to not go with the 26650? Also will protected batteries fit in this host as I much prefer them over unprotected cells whenever possible.

The last is about shipping since I live about 600 miles (1000km) north of Hak in Iowa I'm guessing shipping to him first wouldn't save much if anything on shipping. Honestly since I tend to be an impatient SOB when it comes to waiting for new "toys" to arrive I'd probably just opt for the 3-5 day shipping since at $20 it's offered at a very reasonable cost.

JETLASERS · May 29, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

LtKernelPanic said:
Hmm. If these prices are going to be good past May 31st getting one of the 473nm listed in the OP is almost a certainty.

I do have a couple quick questions for either Gray or Hak. I see the 473nm in the PL-E Pro can use either 18650 or 26650 batteries but I assume given the choice a 26650 would be the better option. I have to order a bunch of batteries for other lasers/lights anyways so is there a reason to not go with the 26650? Also will protected batteries fit in this host as I much prefer them over unprotected cells whenever possible.

The last is about shipping since I live about 600 miles (1000km) north of Hak in Iowa I'm guessing shipping to him first wouldn't save much if anything on shipping. Honestly since I tend to be an impatient SOB when it comes to waiting for new "toys" to arrive I'd probably just opt for the 3-5 day shipping since at $20 it's offered at a very reasonable cost.

Hello LtKernelPanic,
Thanks for your attention and you're right that PL-E Pro lasers take a single 18650 or 26650 and the reason why 26650 is more preferable is probably that PL-E Pro laser is a 26650 host itself and 26650 batts usually have more mah and they are considered to last longer than 18650 which ranges mainly from 2100mah to 3100mah - sure regarding the battery life, it is not 100% true.

For 18650s, we also recommend sanyo 2600mah and samsung 2800mah unprotected batts which were tested by us to last decently long. Yes, protected 18650s and 26650s are also fine and make sure they are flat top type and of same length with flat top 18650/26650 otherwise the threads might not fit perfectly but it will work anyway.

Speaking of shipping, as Hak has been stocking a variety of batts like 18650/26650/14500/16650, if you source batts from him, it will be a better option
our shipping the laser to him first and if you just wanna get the PL-E Pro laser body asap regardless of batts things, shipping to you directly from China via UPS is probably the better options.

Thanks! :）

hakzaw1 · May 29, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

LtKernelPanic said:
Hmm. If these prices are going to be good past May 31st getting one of the 473nm listed in the OP is almost a certainty.
I dont know this for certain but I think you will be able to enjoy these prices For a bit longer
I do have a couple quick questions for either Gray or Hak. I see the 473nm in the PL-E Pro can use either 18650 or 26650 batteries but I assume given the choice a 26650 would be the better option. I have to order a bunch of batteries for other lasers/lights anyways so is there a reason to not go with the 26650? Also will protected batteries fit in this host as I much prefer them over unprotected cells whenever possible.

These 26650s that I have here for JL/Gray are quite good- 4000mAh and priced right. bfore you buy elsewhere allow me to give you a quote on your needs. The shipping get reasonable if you buy more as Fed Ex charges us the same for a single battery as they do for a pound of them. BUT sorry none of the li-ions I have here are button tops. All are flat toppers. IIRC the main advantage is the extra circuit mainly keeps the battery from draining completely ( a bad thing to do to a Li-ion) but JL lasers are made wth the use of button tops in mind- this is the reason in a few cases that we place a spacer(magnet) to make a good connection

The last is about shipping since I live about 600 miles (1000km) north of Hak in Iowa I'm guessing shipping to him first wouldn't save much if anything on shipping. Honestly since I tend to be an impatient SOB when it comes to waiting for new "toys" to arrive I'd probably just opt for the 3-5 day shipping since at $20 it's offered at a very reasonable cost.

I too get antsy waiting but even tho you wont save a lot of $$ by sending to me first you will get a good inspection- a Power graph and there will be a savings by letting me send you everything including batts and/or a niteCore i2. On very few rare occasions some JLs did not pass my inspection- and the buyer would not have liked to get it directly . I send it back at JLs expense and a better one is shipped ASAP- just filling out all the forms at the PO is a big PITA- if you don't do it right even more delays can happen aside form a bigger cost to return. So it can be a trade-off.

JETLASERS said:
Hello LtKernelPanic,
Thanks for your attention and you're right that PL-E Pro lasers take a single 18650 or 26650 and the reason why 26650 is more preferable is probably that PL-E Pro laser is a 26650 host itself and 26650 batts usually have more mah and they are considered to last longer than 18650 which ranges mainly from 2100mah to 3100mah - sure regarding the battery life, it is not 100% true.

For 18650s, we also recommend sanyo 2600mah and samsung 2800mah unprotected batts which were tested by us to last decently long. Yes, protected 18650s and 26650s are also fine and make sure they are flat top type and of same length with flat top 18650/26650 otherwise the threads might not fit perfectly but it will work anyway.

Speaking of shipping, as Hak has been stocking a variety of batts like 18650/26650/14500/16650, if you source batts from him, it will be a better option
our shipping the laser to him first and if you just wanna get the PL-E Pro laser body asap regardless of batts things, shipping to you directly from China via UPS is probably the better options.

Thanks! :）

Judging by past experience the quicker way and not all that more expensive way would be to have Gray ship directly with you especailly if he is able to do that THIS time for only $20-the Odds are greatly in favor of a perfect laser coming direct from JK- and in light of a few probelms lately I am sure that a tighter control will be used to avoid any problems like those with the tailcap.

JL chose to make the laser ready for the longer protected cells- thus the need, on occasion, for the use of a magnet spacer- to make the laser shorter would mean the longer battery would be a bit too long and the tailcap would have a small gap created by the extra length of the battery.

ALSO-- I recently had a problem with another brand of 26650 battery- it had a paper label that made it a VERY tiny bit bigger- the KKs slide in and out with no problems-( but you can see that there is not much extra room for a 'thicker' abtt) but if you use any battery that is the size of the one ... problems....that one took a long time to remove (a vacuum was caused and getting it out was not easy) now if this had been with a Pro as it comes apart the battery could have been easily 'pushed' out -- this was a not a Pro and the front and batt tube are glued together- so the only option was to pull it out and there is no easy way to get it out---BOTTOM line- On ANY laser take care to avoid any battery that you must use some force to insert- in a JL laser as the tolerance is , while perfect for KKs, is too tight for any 26650 that may have a greater diameter..

LtKernelPanic · May 31, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

Thanks for the replies Gray and Hak. I was going to reply last night until a near by exploding tree made me think better of turning on the computer.

Glad to hear the hosts will work with protected cells. I managed to run three of my 10440s down to between .5-.75v once because I forgot to unhook a driver I was designing from my test load. They still work but don't charge to the full 4.2v anymore.

I'll try the batteries I ordered for my other stuff first since I needed them anyways and if they're not the right fit I'll definitely be in contact with Hak to get some from him.

Anyhow Gray I'll be PMing you for ordering info soon I think.

JETLASERS · Jun 2, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

LtKernelPanic said:
Thanks for the replies Gray and Hak. I was going to reply last night until a near by exploding tree made me think better of turning on the computer.
Glad to hear the hosts will work with protected cells. I managed to run three of my 10440s down to between .5-.75v once because I forgot to unhook a driver I was designing from my test load. They still work but don't charge to the full 4.2v anymore. I'll try the batteries I ordered for my other stuff first since I needed them anyways and if they're not the right fit I'll definitely be in contact with Hak to get some from him.
Anyhow Gray I'll be PMing you for ordering info soon I think.

Okay no problem dont hesitate to pm me if i can help - have a nice weekend!

Smeerworst · Jun 4, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

Wanted to let you all know and thank gray for shipping a new tailcap to me.

Did a 7min LPM run with it on a 18650 cell, and it stayed above 800mW

with peaks over 1W.

Does for 5 min a lovely 850mW without much dipping

Thank you gray!

I have a LPM with power graph in the works for me.
So much easyer then making video's, but if you want i can upload it.. but not today

''it's late''

Also got a couple of KK 26650's comming.

:beer: Sm.

hakzaw1 · Jun 5, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

GREAT^^ another happy ending- Gray has a knack for doing that--

I will jump in here and say i have some worries about how hot the Pl-E Pro 532/300 got last night during my LPM power graphing session-

the first of these 3 min runs I was underwhelmed-

but the laser had been stored in a well a/c-ed room and the power did start to climb towards the end and became more stable- i watched the meter continue to climb after the graphng stopped for another 30 sec or so. and shut the laser down.

(it was on the ac/dc wall wart ($12) from JL) I got my the second graph ready on my laptop for test #2, and I did not time this, but it was on stand-by (rest)for at least two/three minutes- the leds were on the entire time...
I started #2 and the results were better however at the end of the 180 sec run the laser was more than 'just warm' and it felt like the part to the rear was hotter- ? could this mean the heat was from the driver?++

was/is 8 vdc@ 5A from the wart providing too much and that is turning to heat on the driver??

I realize that being DPSS more of the front part is taken up by not only the internal focus system but the parts in front of the IR Pump. .SO I let it cool completely down-but never seeing 'under the hood' i may be wrong about the drivers location in there...

did a much better test #3 and both the peak and average were better and at the end of the 3 mn test the laser was barely warm- The wall wart 'SEZ' 8vdc at 5A but if you have ever measured a wall wart on a DMM you know that they can be much higher VDC= or lower that the labels and no load makes a diff reading too.

My plan for this 300 mW it to use it only with a single KINGKONG and keep the run time below 3 or 4 min.. I have tested many PL-E lasers and the only huge diff between one or multiple batts of all sizes seems to be mostly in the run time and not very much on the output--

here are some pics- will ad actual graph later when I am ay my 'office'.

''' Lunitic Fringe' is playing on the oldies radio station- note to self: make a laser show to go with this CRAZY good song..

hakzaw1 · Jun 5, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

B U M P and an offer for short sale..

*************************

UP FOR GRABS... brand new-- used briefly mostly for testing- ships from TEXAS.

Full 6 month warranty.

The GB prices for PL-E PRO is :
PL-E Pro 532nm 300 mW: 300$

comes with second barrel- threaded lens cap on a 'dont lose me' lanyard ( its also on there to remind you to NEVER touch the tailcap button with the lens cover in place NEVER!!!!)

free sleeve to make use of 18650 Li_ion(9$)

+from Gray one free glass high quality diffraction grating

and from Hak and Chuck at AixiZ Laser Houston some free laser warning stickers.

other freebies will depend upon my mood--lol

payment by personal check- bank MO or the best and safest a $1.99 USPS MO - sent to me in a P.O. envelope for better safer sending to me-take a pic of the instrament.(check or MO)

sorry PP does not allow use for lasers over 5mW.

Cash is king --local pick-up is free and comes with a free adult beverage.
The pics of the graph are in the above post- more pics later-
you must be 18 or older and prove that and ownership of eye ware for green lasers-

I do want the buyer to send a 1$ payment for goods( NOT personal or gift) to my paypal to confirm your verified home addy--and print your shipping label.

do not email me or any other LPF member unless you add your LPF username.
same goes for PP comms- do ask us to guess who you are...

I will also need a phone number for the shipper,,
ATM no one has 'dibbs' on this laser. it passes all my tests nice beam profile very good divergence no artifacts stable as any high power DPSS- the beam is true- the new metal on/off button is BIG improvement. PM if you want her--

Shipping only to CONUS $16.00 with track and insurance USPS.

i will add ONE free new Kingkong 26650 4,25 vdc 4000mAh GOLD!!

add $15 if you want one of my last nitecore i2 smart chargers.

PM for more info

VR--hak

wbp · Jun 6, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

My PL-E Pro 532/400 arrived today - what a monster! It's almost a work of art, I can't wait until I get a chance to put it to use in my programs.

I have to say a huge thank you and kudos to Gray for all of your support and accommodating my requests. It has been a real pleasure doing business with you!

I also have an older PL-C with a failed switch - he sent a replacement switch with the PL-E. It's now installed and my PL-C is working perfectly again. What great customer service!

I've done business with a lot of people and few have the integrity and obvious genuine good customer service that Gray and Jetlasers have.

William

LtKernelPanic · Jun 6, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

^
Great to hear!

I'm just waiting until payday tomorrow so I can pay the rest of my bills and then finally request a final quote from him for one of those sweet 473s!

JETLASERS · Jun 7, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

hakzaw1 said:
GREAT^^ another happy ending- Gray has a knack for doing that--

I will jump in here and say i have some worries about how hot the Pl-E Pro 532/300 got last night during my LPM power graphing session-

the first of these 3 min runs I was underwhelmed-

but the laser had been stored in a well a/c-ed room and the power did start to climb towards the end and became more stable- i watched the meter continue to climb after the graphng stopped for another 30 sec or so. and shut the laser down.

(it was on the ac/dc wall wart ($12) from JL) I got my the second graph ready on my laptop for test #2, and I did not time this, but it was on stand-by (rest)for at least two/three minutes- the leds were on the entire time...
I started #2 and the results were better however at the end of the 180 sec run the laser was more than 'just warm' and it felt like the part to the rear was hotter- ? could this mean the heat was from the driver?++

was/is 8 vdc@ 5A from the wart providing too much and that is turning to heat on the driver??

I realize that being DPSS more of the front part is taken up by not only the internal focus system but the parts in front of the IR Pump. .SO I let it cool completely down-but never seeing 'under the hood' i may be wrong about the drivers location in there...

did a much better test #3 and both the peak and average were better and at the end of the 3 mn test the laser was barely warm- The wall wart 'SEZ' 8vdc at 5A but if you have ever measured a wall wart on a DMM you know that they can be much higher VDC= or lower that the labels and no load makes a diff reading too.

My plan for this 300 mW it to use it only with a single KINGKONG and keep the run time below 3 or 4 min.. I have tested many PL-E lasers and the only huge diff between one or multiple batts of all sizes seems to be mostly in the run time and not very much on the output--

here are some pics- will ad actual graph later when I am ay my 'office'.

''' Lunitic Fringe' is playing on the oldies radio station- note to self: make a laser show to go with this CRAZY good song..

Thanks! :yh:Yes, the ac adapter will generate more heat than batts - so keeping it <3mins is okay. 5V5A ac adapter is better - we should have chosen 5v5a but in order to simplify things and make all PL-E Pro wavelengths like 445nm and 532nm share a same ac adapter, we made it more voltage tolerant.

JETLASERS · Jun 7, 2013

Re: GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

wbp said:
My PL-E Pro 532/400 arrived today - what a monster! It's almost a work of art, I can't wait until I get a chance to put it to use in my programs.

I have to say a huge thank you and kudos to Gray for all of your support and accommodating my requests. It has been a real pleasure doing business with you!

I also have an older PL-C with a failed switch - he sent a replacement switch with the PL-E. It's now installed and my PL-C is working perfectly again. What great customer service!

I've done business with a lot of people and few have the integrity and obvious genuine good customer service that Gray and Jetlasers have.

William

Thanks for your kind words, William! Glad you also made the PL-C laser work - you are the engineer!

GB#1st of PL-E Pro Lasers and PL-E 2.0/3.0 Clearance - May 2013

JETLASERS

0

Sparkys

0

JETLASERS

0

hakzaw1

0

LtKernelPanic

0

JETLASERS

0

hakzaw1

0

LtKernelPanic

0

JETLASERS

0

Smeerworst

0

hakzaw1

0

Attachments

hakzaw1

0

wbp

0

LtKernelPanic

0

JETLASERS

0

JETLASERS

0

Online statistics

Forum statistics

Share this page