Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Wicked Lasers Spyder III

Status
Not open for further replies.
Hemlock_Mike

Hemlock_Mike

0
Joined
Jan 7, 2007
Messages
6,309
Points
83
Any object hit with sufficient power will start to ablate matter energitcally causing some thrust. It's too late for me to worry about it -- I was joking but that is a real question someone may answer. Think about one of those old radiometers in a vacuum bulb.

HMike
 
Last edited:





f22warzone

f22warzone

0
Joined
Sep 8, 2007
Messages
759
Points
0
Hemlock_Mike said:
Any object hit with sufficient power will start to ablate matter energitcally causing some thrust. It's too late for me to worry about it -- I was joking but that is a real question someone may answer. Think about one of those old radiometers in a vacuum bulb.

HMike
Click to expand...

lol talking about old radiometers my RPL will make it spin very fast if you enlarge the spot if not i accidentally burned the coating off a little...... didn't know you could see smoke in a vacuum.
 
diachi

diachi

0
Joined
Feb 22, 2008
Messages
9,700
Points
113
ElektroFreak said:
Nice fair review Diachi!

Recently I found out that expecting pure TEM00 output and full stability from a Chinese DPSS over 500mW is asking too much. The vast majority of Chinese manufaturers list ALL of their >500mW green DPSS lasers as being "near TEM00" which could mean anything.. I'm not trying to say that your unit should be unstable and drop to 100mW after a bit, but things get very different when you get into high-powered linear cavity lasers.
Click to expand...


The spec sheat on WLs site specifys TEM00 though. This operates across about 5 different modes. TEM00 sometimes, TEM01 and TEM01* are the most frequent, then a micture of different modes happens too.

The spyder is good for shrinking heatshrink tubing though ;).
 
E

ElektroFreak

0
Joined
Nov 7, 2008
Messages
5,725
Points
0
Getting the Chinese to post accurate specs is like pulling teeth. Given that your laser is listed as being 400mW, I think you have cause to tell Steve about it. While it is true that getting very high powers (600-700 mW and up) from a linear cavity DPSS and have TEM00 output and good power stability is pretty much impossible, they should be able to provide 400-500mW plus of stable power for that cost.
 
L

LaserRX

0
Joined
Apr 30, 2008
Messages
104
Points
0
It's possible it was banged around in shipping. I'd also suggest shooting Steve an email.
 
diachi

diachi

0
Joined
Feb 22, 2008
Messages
9,700
Points
113
LaserRX said:
It's possible it was banged around in shipping. I'd also suggest shooting Steve an email.
Click to expand...


That's not what is causing this. My unit was like this BEFORE being sent. According to the power graph supplied with it.

I've not had much time lately to contact steve or post back. I have a lot of school work and stuff with my band on atm. I'll try and find some time to actually remember to do it.
 
scopeguy20

scopeguy20

0
Joined
Jun 28, 2007
Messages
3,443
Points
63
diachi, I know this is an old thread, but did you find there is no TEC in the Spyder III? (PM also sent) -Glenn
 
yobresal

yobresal

0
Joined
Nov 5, 2007
Messages
4,919
Points
83
This laser is now in my possesion. Perhaps I could measure the power draw and depending on efficiency of the laser that should be able to give us an idea as to whether or not there is a TEC draingin the battery. I highly doubt it though as the battery life is pretty remarkable for the amount of power this thing is putting out.
 
W

wickedALEX

0
Joined
Jan 3, 2008
Messages
128
Points
18
BuildAbluraylaser said:
Oh yeah I remember those, but me I'm talking about a situation where there's no vacuum.
Click to expand...

Well with my 2MW pulsed YAG laser it is possible.
You can move like small pieces of charcoal.
The laser forms a plasma explosion on the surfac and that gives it the thrust.
 
swimminsurfer256

swimminsurfer256

0
Joined
Dec 25, 2009
Messages
1,251
Points
48
I didn't know the host of the spyders was that big! Looks awesome... A bit silly about the mode hopping issue and the "continuous" duty cycle.. I wouldn't have believed it for a laser of that power from WL anyways :p
 
A

anthony2823

0
Joined
May 6, 2012
Messages
3
Points
0
i know this is an old thread but a quick question. The poster stated a 3500$ price tag!!!!

back in 2008 was that a common price for a 500mW laser? Just curious and thank you for any responses.
 
daguin

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
Yes (especially at WL).

Prices have come down significantly since then

Peace,
dave
 
Status
Not open for further replies.




Top