Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

So I bought a green laser on eBay...

Joined
Oct 2, 2011
Messages
18
Points
0
On the topic of batteries-- AAAs don't seem to be enough for this thing. I've gone through several pairs of AAAs by now. Should I switch to AAs? I could probably fit up to a C battery holder on the gun.
 





Joined
Aug 14, 2011
Messages
1,109
Points
0
On the topic of batteries-- AAAs don't seem to be enough for this thing. I've gone through several pairs of AAAs by now. Should I switch to AAs? I could probably fit up to a C battery holder on the gun.

You'll probably have to end up using lithium ion batteries as they can supply more current to the diode. Regular AAAs just don't have what it takes.
 
Joined
Oct 2, 2011
Messages
18
Points
0
Yeah, I was just using alkalines. I'll pick some Li-Ions up next time I go out. Thanks for the tip!

EDIT: Maybe I should be a bit more clear with my problem, as I'm not 100% sure it's the batteries at all.

When I first got this laser, it worked absolutely flawlessly. When I first hooked it up to my prototype board, it worked flawlessly. The only other things on the board are a tact switch, a 3V piezo buzzer and a single green LED. Now, for some reason, when I first activate the laser, it is dim. I chalked this up to weak batteries. HOWEVER, when I leave the thing powered for a minute or so, it gradually builds up to full power (or at least close to it) and stays there until I leave it powered off for a while, which makes it go back to starting off dim. Is this just a case of current draw problems, or is something wrong with the laser itself?
 
Last edited:
Joined
Oct 2, 2011
Messages
18
Points
0
Diode's dead. Project ruined. Halloween cancelled.

I hooked it up to a 3.7V cell phone li-ion and it no longer works, even at lower voltage. I thought it could work up to 4.2V but apparently I was wrong! So much for my first laser. $30 down the drain and now I'm broke.

UPDATE: Getting a free replacement. I'm a pretty good liar. :p

Hopefully it gets here before halloween.

I think I know what happened, in retrospect. I had the pot turned down a bit, which was working alright on AAAs. The new battery was probably too much for it at that setting. It's a 3.7V Samsung cell phone rechargeable, 1000 mAh.
 
Last edited:
Joined
Sep 12, 2007
Messages
9,399
Points
113
If anything, having the pot lower would have saved it. Either you hooked up something incorrectly, or it was operating near max power dissipation on AAAs to begin with.
 
Joined
Oct 2, 2011
Messages
18
Points
0
If anything, having the pot lower would have saved it. Either you hooked up something incorrectly, or it was operating near max power dissipation on AAAs to begin with.

Yeah, I'm pretty sure the pot being turned up is what did it. I wasn't even thinking about that. Mistakes are to be learned from, not forgotten. I will definitely have the pot turned down before I plug the new one in.

Any other safety measures I can take?
 
Last edited:
Joined
Oct 2, 2011
Messages
18
Points
0
Well, I have just been informed by the seller that adjusting the lens could 'damage' the diode. Complete bullshit, right?
 

LaZeRz

0
Joined
Feb 19, 2011
Messages
2,549
Points
63
LOL, Thats pretty stupid on their part.

If you know what your doing, then by all means, go ahead!
 

djayz

0
Joined
Oct 13, 2011
Messages
68
Points
0
Do some experiments and kill some diodes, and the fun part is let the new stuff keep coming.. the fun never ends.
 

RichA

0
Joined
Sep 25, 2010
Messages
5
Points
0
Wow! I'm surprised they could even communicate with you, unless you know Mandarin. Chinese Junk used to be the name of a type of ship, now it just means most electronics.
 
Last edited:
Joined
Oct 2, 2011
Messages
18
Points
0
Wow! I'm surprised they could even communicate with you, unless you know Mandarin. Chinese Junk used to be the name of a type of ship, now it just means most electronics.

Well, the guy himself was from Tennessee. :p

I got my new laser and I'm trying to mount it in the barrel of this gun. the laser is a bit too small and I need to figure out a way to do it so the laser is aimed properly, without screws.
 

RichA

0
Joined
Sep 25, 2010
Messages
5
Points
0
Well, the guy himself was from Tennessee. :p

I got my new laser and I'm trying to mount it in the barrel of this gun. the laser is a bit too small and I need to figure out a way to do it so the laser is aimed properly, without screws.

Unless it's specifically machined (or a sleeve machined for it) it will be tough to align without some kind of screws or other alignment devices.
 
Joined
Oct 2, 2011
Messages
18
Points
0
I managed to drill through the barrel and get screws in to align it, but the project failed in another unforseen way. The glue I used to secure the tact switch ended up working for a few minutes, and then somehow seeped into the switch and locked it up completely. I may be able to fix it in the future, but for right now, the project is cancelled. I'm tired of it. The laser still works, and I'll take some pictures of it working while hotwired together later today.
 
Last edited:




Top