Old 05-15-2010, 12:20 PM #1
Banned
 
Join Date: Apr 2010
Location: australia
Posts: 173
Rep Power: 0
GreenLaser is infamous around these partsGreenLaser is infamous around these parts
GreenLaser GreenLaser is offline
Banned
 
Join Date: Apr 2010
Location: australia
Posts: 173
Rep Power: 0
GreenLaser is infamous around these partsGreenLaser is infamous around these parts
Default ??test if rkcsr driver is dead.

my rkcstr driver has only been fed 7-9v and i just woud connect the output pads to my multimeter set on 200m setting it would read around 65 and i could adjust it to over 100. but now it reads nothing?? how do i test if it is dead


GreenLaser is offline   Reply With Quote


















Old 05-15-2010, 12:33 PM #2
Pontiacg5's Avatar
Class 3B Laser
 
Join Date: Dec 2007
Location: Ottawa, Kansas
Posts: 2,524
Rep Power: 122
Pontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond repute
Pontiacg5 Pontiacg5 is offline
Class 3B Laser
Pontiacg5's Avatar
 
Join Date: Dec 2007
Location: Ottawa, Kansas
Posts: 2,524
Rep Power: 122
Pontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond reputePontiacg5 has a reputation beyond repute
Default Re: ??test if rkcsr driver is dead.

I'm not sure but I think you are not supposed to run those without a load. The multimeter might provide enough of a load to keep it going but when you disconnect the meter it would run with no load and break.

I know the boost drive cannot be run without a load, I'm not sure about the Rkcstr though. You should build a test load, you can get everything you need at radioshack very cheap or in broken electronics you have around the house.
Pontiacg5 is offline   Reply With Quote
Old 05-15-2010, 12:37 PM #3
Banned
 
Join Date: Apr 2010
Location: australia
Posts: 173
Rep Power: 0
GreenLaser is infamous around these partsGreenLaser is infamous around these parts
GreenLaser GreenLaser is offline
Banned
 
Join Date: Apr 2010
Location: australia
Posts: 173
Rep Power: 0
GreenLaser is infamous around these partsGreenLaser is infamous around these parts
Default Re: ??test if rkcsr driver is dead.

arrrr f*&k ing hell damit that friver was 30 dollars to australia.
everyone also pls visit this and have your input and tell me if this is right http://laserpointerforums.com/f44/dd...ing-50782.html
cheers
GreenLaser is offline   Reply With Quote
Old 05-15-2010, 07:58 PM #4
chipdouglas's Avatar
Class 3B Laser
 
Join Date: Dec 2008
Location: Riverside, California
Posts: 4,011
Rep Power: 139980
chipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond repute
Send a message via Yahoo to chipdouglas
chipdouglas chipdouglas is online now
Class 3B Laser
chipdouglas's Avatar
 
Join Date: Dec 2008
Location: Riverside, California
Posts: 4,011
Rep Power: 139980
chipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond reputechipdouglas has a reputation beyond repute
Send a message via Yahoo to chipdouglas
Default Re: ??test if rkcsr driver is dead.

you can run the rkcstr with out load but you cant test it with out a load. you need a test load so your meter can read something.

and quit asking about your driver etching....we are not lawyers. you have already been told the best advice which is to contact daedal.



michael
__________________
IN A CONSTANT STATE OF PICNIC

I AM THE STATUS QUO

ARE YOU A NEW MEMBER, OR EVEN MORE, ARE YOU NEW TO ONLINE FORUMS... READ THIS
LASER POINTER FORUM ETIQUETTE


for pot modding facts click below

http://laserpointerforums.com/f51/pot-modding-faqs-40510.html
chipdouglas is online now   Reply With Quote
Reply





Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



























Privacy Policy | Advertising Disclaimer | Terms of Use


 


All times are GMT. The time now is 11:57 AM.


Powered by: vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO
Privacy Policy | Advertising Disclaimer | Terms of Use
Copyright (C) 2017 Laser Pointer Forums, LLC