- Joined
- Mar 2, 2008
- Messages
- 1,500
- Points
- 0
my dx true 50mW greenie is mode hopping and now it wont burn :'(
is there any way to fix this mode hopping ?
is there any way to fix this mode hopping ?
LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
mode hop help !!
- Thread starter wesdaman14
- Start date
- Joined
- Feb 8, 2008
- Messages
- 728
- Points
- 16
Definition: the phenomenon that a laser makes sudden transitions other modes of its resonator
Mode hopping is a phenomenon which is mostly discussed in the context of single-frequency lasers. Such a laser may operate on a single resonator mode for some time, but then suddenly switch to some other mode. This means that this other mode suddenly takes over all the optical power; for a short while, there may be power in both modes.
In multi mode operation of a laser, there may also be transitions between different sets of modes. However, simultaneous oscillation on many modes is then most common, and instead of complete mode hops there are often more continuous transitions, with the optical power being gradually redistributed. The dynamics can be further influenced by nonlinear effects such as e.g. spatial hole burning.
Mode hops can also involve higher-order modes, or modes with different polarization in lasers with polarization-independent gain.
Causes for Mode Hops
Mode hops are often provoked by external influences. For example, a drift of the temperature of the gain medium will shift the wavelength of maximum gain while not shifting the frequencies of the resonator modes to the same extent. (This can happen e.g. in laser diodes, where temperature changes usually affect the gain maximum more than the cavity resonances.) The previously lasing mode may then no more be the mode with highest gain, so that the power of a competing mode with higher gain can quickly rise.
Essentially the same phenomenon can occur for length drifts of the laser resonator, which shift the resonator mode frequencies without also shifting the gain maximum.
Both origins of mode hops often result from attempts to tune the wavelength of a laser. The external influences can of course also be just random noise, e.g. mirror vibrations, temperature fluctuations, changes of pump power, etc., or external optical feedback.
Consequences of Mode Hops
Mode hops can obviously be rather disturbing, because they can make it difficult e.g. to obtain continuous wavelength tuning. Depending on various details of a laser setup, the wavelength may make significant jumps with only small changes in between these jumps, or it can vary like a sawtooth curve.
Mode hops also generate laser noise, e.g. in the form of intensity noise and noise of other parameters, particularly if the mode hops occur rather often.
Avoiding Mode Hopping
It is generally easier to avoid mode hopping when the laser resonator has a large free spectral range, i.e., a large frequency spacing of its fundamental modes. Some tunable lasers are just equipped with a correspondingly short laser resonator, and the tuning range is limited by a value close to the free spectral range, which may e.g. be a few gigahertz for a compact non-planar ring oscillator (NPRO or MISER).
A continuous (mode-hope-free) tuning range much wider than the free spectral range is possible by coordinated tuning of the resonator mode frequencies and the gain maximum, or with an additional intra-cavity optical filter.
Random mode hops may be suppressed by minimizing external noise influences (e.g. by temperature stabilization) and also by using a resonator with large free spectral range (see above).
It is also possible to employ various kinds of nonlinearities which favor the already lasing mode over competing modes. An example is spatial hole burning in an unpumped region of a quasi-three-level gain medium. A similar effect can be achieved with intra-cavity frequency doubling.
Wow that was pretty dang long
Mode hopping is a phenomenon which is mostly discussed in the context of single-frequency lasers. Such a laser may operate on a single resonator mode for some time, but then suddenly switch to some other mode. This means that this other mode suddenly takes over all the optical power; for a short while, there may be power in both modes.
In multi mode operation of a laser, there may also be transitions between different sets of modes. However, simultaneous oscillation on many modes is then most common, and instead of complete mode hops there are often more continuous transitions, with the optical power being gradually redistributed. The dynamics can be further influenced by nonlinear effects such as e.g. spatial hole burning.
Mode hops can also involve higher-order modes, or modes with different polarization in lasers with polarization-independent gain.
Causes for Mode Hops
Mode hops are often provoked by external influences. For example, a drift of the temperature of the gain medium will shift the wavelength of maximum gain while not shifting the frequencies of the resonator modes to the same extent. (This can happen e.g. in laser diodes, where temperature changes usually affect the gain maximum more than the cavity resonances.) The previously lasing mode may then no more be the mode with highest gain, so that the power of a competing mode with higher gain can quickly rise.
Essentially the same phenomenon can occur for length drifts of the laser resonator, which shift the resonator mode frequencies without also shifting the gain maximum.
Both origins of mode hops often result from attempts to tune the wavelength of a laser. The external influences can of course also be just random noise, e.g. mirror vibrations, temperature fluctuations, changes of pump power, etc., or external optical feedback.
Consequences of Mode Hops
Mode hops can obviously be rather disturbing, because they can make it difficult e.g. to obtain continuous wavelength tuning. Depending on various details of a laser setup, the wavelength may make significant jumps with only small changes in between these jumps, or it can vary like a sawtooth curve.
Mode hops also generate laser noise, e.g. in the form of intensity noise and noise of other parameters, particularly if the mode hops occur rather often.
Avoiding Mode Hopping
It is generally easier to avoid mode hopping when the laser resonator has a large free spectral range, i.e., a large frequency spacing of its fundamental modes. Some tunable lasers are just equipped with a correspondingly short laser resonator, and the tuning range is limited by a value close to the free spectral range, which may e.g. be a few gigahertz for a compact non-planar ring oscillator (NPRO or MISER).
A continuous (mode-hope-free) tuning range much wider than the free spectral range is possible by coordinated tuning of the resonator mode frequencies and the gain maximum, or with an additional intra-cavity optical filter.
Random mode hops may be suppressed by minimizing external noise influences (e.g. by temperature stabilization) and also by using a resonator with large free spectral range (see above).
It is also possible to employ various kinds of nonlinearities which favor the already lasing mode over competing modes. An example is spatial hole burning in an unpumped region of a quasi-three-level gain medium. A similar effect can be achieved with intra-cavity frequency doubling.
Wow that was pretty dang long
