Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Building 473nm Laser - Need TEC Supplier!






diachi

0
Joined
Feb 22, 2008
Messages
9,700
Points
113
yup, greens a good bit easier to achieve than blue though :p Not saying that green is easy or anything, it's just easier than blue.

-Adam
 

viroy

0
Joined
Mar 20, 2008
Messages
126
Points
0
wow cool, thats alot of power.
you just need one crystal right? using a 808nm diode through a ??? crystal then collimator correct?
Can I ask where you get the crystals?
 
Joined
Oct 20, 2008
Messages
351
Points
0
viroy said:
wow cool, thats alot of power.
you just need one crystal right? using a 808nm diode through a ??? crystal then collimator correct?
Can I ask where you get the crystals?

You have make the crystals in perfect place and keep it there and dont forget keeping the diode still housing it soldering batteries and all that stuff but crystals and tech are the hardest but alinging them that super annoying.

Better off buying a blue ::)
 

viroy

0
Joined
Mar 20, 2008
Messages
126
Points
0
so for 532nm... looks like a nd:yvo4 crystal? do you need a KTP crystal after that or is that a part of the yvo4 crystal?

What crystals are used for 473nm?
 
Joined
Apr 30, 2008
Messages
104
Points
0
Nd:YAG and ND:YVO4 can both be used in combination with LBO in order to get 473nm.  However, the 946nm line is quite weak compared to the 808nm.  It will take much more then 2 watts to generate 500mW 473nm unfortuantely. I would be happy with a stable 40mW from this.

Most YAG rods are..well rods, this looks like ND:YVO4, which is more efficient anyway.  However you need to be careful with ND:YVO4 and how much pump power you use, more then 2 watts will usually cause grey lining over time, which is why YAG is normally used when the pumps get to this power and higher.
 
Joined
Nov 7, 2008
Messages
5,725
Points
0
viroy said:
so for 532nm... looks like a nd:yvo4 crystal? do you need a KTP crystal after that or is that a part of the yvo4 crystal?

What crystals are used for 473nm?

For a standard lower-power green setup the order is: pump diode => beam correction lens/optics => Nd:YVO[sub]4[/sub] => KTP => OC

I've never built a blue system, but know that for 473nm they use Nd:YVO[sub]4[/sub] or YAG plus LBO instead of KTP.

For the most practical DIY system I recommend using composite or hybrid crystals. These contain both Nd:YVO[sub]4[/sub] and KTP along with all necessary coatings in one small crystal. Then all you need is a pump source and an output lens. This minimizes the amount of alignment necessary to achieve a decent output with good beam quality. They can be obtained on ebay premounted in a tiny heatsink here: http://cgi.ebay.com/Nd-yvo4-Ktp-Glu...53141QQcmdZViewItemQQ_trksidZp1742.m153.l1262

They can also be purchased in high- and low-power sizes from CASIX here: http://casix.com/product/prod_opt_laser_dpm.html
 

viroy

0
Joined
Mar 20, 2008
Messages
126
Points
0
I found another nd:yvo4 crystal but it says coatings = HR-1064/532, HT808 S2: AR-1064/532
So I couldnt use one like this to make blue right? I would have to find one coated 946/473?
Also, I have seen some using a "BiBo" crystal... what is the best to use for pumping 1w of 808nm(T05)?

Curious... What does each crystal do? why do i need 2?
 
Joined
Mar 8, 2008
Messages
2,669
Points
48
I hate to  rain on anyone's parade.... but getting any blue out of a 1W T-O5 will be very very impressive.

There is a reason these blue lasers cost so much, and it isn't materials cost. Blue is very hard to make. I have a 2.5W c-mount pump with a yag and good sized LBO, all with the correct coatings. I've made a lot of  crystal sets lase green (and no, not bonded sets that you just stick in front of a pump and get green. The ones with separate components and OC's that need to be aligned perfectly) and I've yet to get more than a mW of blue. Alignment and stability is very tough on a 473nm laser, everything (alignment and temperature) needs to be flawless to get any sort of respectable output. You'll need custom machined mounts to hold everything in perfect alignment, and then be able to adjust them on top of that.

I'm not saying that it cant be done, but just know that its much much much much harder than green.

for 500mW of 473 you're looking at around 10W of pump power, or more.

Also if you are going for a 'hand-held' design, which is even tougher than a lab-style, I think most pointers use BBO crystals.    

You'll need a yag coated as follows: [highlight]S1[/highlight]: HT: 808,1064,1319    HR: 946/473   [highlight]S2[/highlight]: AR 946, 473

Then you should also have your doubling crystal coated on both sides for AR 946 and 808

Then your output coupler needs to be Plano concave with an ROC of 50 to 100. [highlight]S1[/highlight]: HR 946 HT 473nm  [highlight]S2[/highlight]: AR 473nm

hope that helps you in your endeavor
 

viroy

0
Joined
Mar 20, 2008
Messages
126
Points
0
Thanks for the info!
I will have my CNC mill done sometime in april.
I am building it as a dual-purpose, PCB & Aluminum mill with great accuracy. 4'x2'x4" travel!
So with that, I can achieve near perfect positioning... I will integrate fine tuning capabilities.
 
Joined
May 24, 2007
Messages
283
Points
0
Diachi said:
yup, greens a good bit easier to achieve than blue though  :p Not saying that green is easy or anything, it's just easier than blue.

-Adam

not realy blue is exactly the same as green just needs more pump power and a lbo instead of a ktp
the rest works exactly the same

but since 445 diodes are getting cheap there's no real need to build a 473 anymore

445 nm 500 mw is doing 2300 euros at the moment
 
Joined
Jul 27, 2007
Messages
3,642
Points
63
laserfreak3d said:
[quote author=Diachi link=1227322610/16#17 date=1227913801]yup, greens a good bit easier to achieve than blue though  :p Not saying that green is easy or anything, it's just easier than blue.

-Adam

not realy blue is exactly the same as green just needs more pump power and a lbo instead of a ktp
the rest works exactly the same

but since 445 diodes are getting cheap there's no real need to build a 473 anymore

445 nm 500 mw is doing 2300 euros at the moment[/quote]

Yeah it works the same, but is much more difficult to get it to work :p

I too am hoping 445nm diodes will soon be cheaply available.
 
Joined
Mar 8, 2008
Messages
2,669
Points
48
yeah, works the same. Have you built one? Probably not if you think it's as 'easy' (which still isn't easy!!) as green.

Gain on 946 is much less, it's harder to get the line to lase, not to mention polarization on green doesn't really matter, or at least not as much. It DOES with blue. If the roation of your yag or LBO is off by just a little bit, you wont get any blue. Also, with green as long as you have a clear optical path through the crystals you can probably get it to lase, with Blue or LBO in general, there is a specific path in the the crystal that will allow for the best amount of blue. Also temperature is a huge factor, if your LBO is too hot or cold you wont get any blue at all. There is much more that goes into a blue than a green laser. Like I said before, materials aren't that expensive and yet blue is still a lot more expensive than green.... why do you think that is?

Also, you said there's no 'need' to build a 473nm blue since 445nm diodes are getting cheap. If I 'needed' a blue, I would buy one. When you make one you should be happy if you get any sort of light at all. I'm not building one to make some super strong badass laser, I just want to do it because I'm very interested in the science behind it and the challenge that is associated with it. I already have a 473nm blue that I bought that does close to 200mW.
 




Top