Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

WTB: Oscilloscope

Joined
Dec 27, 2011
Messages
2,062
Points
48
I'm starting to get more interested in the electronics side of things and would like to get a decent oscilloscope. I missed a nice Tek here on the forum a short while back and I am kicking myself for it.

Not only am I looking to buy one, but I am also hoping to pick your collective brains on what I should be looking for, what to avoid and what to pay...

ANY advice would be greatly appreciated.

I was looking into this...

Mixed Signal Oscilloscope - iMSO-104 | Oscium

for my ipad3 and realized that there are full blown scopes for less than that. I also don't know if that is a good solution or not. I'm not against going the iPad route if it looks good - but I have no idea if that is a decent solution.

Thanks in advance for any help!

:)
 





Joined
Dec 11, 2011
Messages
4,364
Points
83
I am also in the market for a scope (purchase pending employment) and wanted to let you know there are certain minimum specs you need to consider if you don't want to waste your money.

1) bandwidth/sampling rate: divide the frequency by 10 and that is the highest frequency you can accurately measure. For example: a 10MHz scope can accurately display/measure a 1MHz signal, but no higher.
2) channel number: a single channel scope is great to see if an oscillator is working, but you won't get a whole lot of troubleshooting done with it. For that you really need two or more channels.
3) beam and trace number: a beam for every channel is ideal as there will be no skipping in the trace drawing, but it isn't a neccessity unless you are planning on working at the top end of your scope's frequency. In a 2 channel 2 trace 10MHz scope, a 1MHz signal will appear to alternate between the two traces as it is drawn across the screen. In a 2 channel 2 beam 10MHz scope there will be no degredation of display.

Btw, it seems it's hard to find a good calibrated used scope above 10MHz for less than $250, but over that amount it isn't hard at all. What is your budget?
 
Joined
Nov 22, 2010
Messages
239
Points
28
Don't buy that ipad toy, and don't buy a Rigol. Tek and Aligent/HP are really the only good scope manufacturers out there, but I guess it all depends on one simple question; How much are you willing to spend, and are you willing to put up with cheap crap if you're spendthrift?

I have a few tek digital storage scopes that could find greater love elsewhere, but I'd need to first know whether you'd be willing to spend $600, $2,000 or $12,000 on one.
 
Last edited:
Joined
Dec 11, 2011
Messages
4,364
Points
83
Oh and that reminds me, Tekpower is NOT the same as Tektronix (the good stuff).

Likewise, the "DSO nano" and its brethren are really just toys. I know they're cheap and approachable, but they're really no good. The only thing they're useful for is scrapping the firmware and converting them in to a MCA (multi-channel analyzers - a type of radiation detection/measurement equipment).

Hey Gren, got an old analog CRT clunker to sell perhaps?
 
Joined
Dec 11, 2011
Messages
4,364
Points
83
I'm probably looking to stay under/around $300. I really am kicking myself for not grabbing the Tek that was up for trade earlier! At the time I didn't realize what it was and that I would be wanting one.

Thanks for the good advice.

I definitely don't want to get into something that is a mess and needs hundreds of dollars worth of calibrating and such.

You and me both. (Both for the price range and the /kickself on the mentioned scope.) I didn't have the money at the time for it though so I don't kick myself too hard. I completely understand not wanting to grab a cheap clunker off eBay that could need repairs and calibration. I've found a few sellers who sell nothing other than refurbished and recalibrated Tektronix scopes at our price level though, and that is what I had intended on going with, should nothing else present itself. If you want I can PM you the eBay store links.

I seem to always hear from various EEs that "people are near giving away great old scopes" yet I never see it happen. I can't help but wonder if they only see it because of their connections in the field, and that being an "insider" is a must.
 
Joined
Jan 2, 2009
Messages
11,800
Points
0
You're seeing it now, LOL.

I have one of these...

http://laserpointerforums.com/f61/tektronix-2430-oscilloscope-48888.html

Not sure if its worth resurrecting or not.

Its has simular fails as this...

Tektronix-2430A-2-channel-150-mhz-digital-oscilloscope-pic-1.jpg
 
Last edited:
Joined
Nov 22, 2010
Messages
239
Points
28
If you decide to spend money on a scope, make sure you buy a digital storage one; they are invaluable for recording transient waveforms.
 
Joined
Jan 2, 2009
Messages
11,800
Points
0
You're in still by the grandfather clause. They changed the password because of a troll.
 
Last edited:

jakeGT

0
Joined
Oct 29, 2010
Messages
3,532
Points
0
And I thought we had finally gotten rid of tsteele in the vet section :crackup:


JK! :beer:
 
Joined
Dec 27, 2011
Messages
2,062
Points
48
So is TJ's scope worth messing with? I'd like a decent scope, but I don't want to end up with a heavy box sitting in a corner that I never could get to work right...
 
Joined
Nov 22, 2010
Messages
239
Points
28
For an uncalibrated scope, yep. For a calibrated one it's a steal, but they haven't connected a probe to the test source so I can't tell...
 




Top