Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Sleds For Sale!  most are $12






millirad

millirad

0
Joined
Apr 28, 2009
Messages
2,416
Points
63
Thanks Glenn, GGW arrived today. Tomorrow I will buy 2 jewellers loupes from harbor-freight for $2.88 each. Soldering wire onto the pins needs to be done when its ten-foot tall. ;-)
 
Flaminpyro

Flaminpyro

0
Joined
May 4, 2009
Messages
5,443
Points
113
GGW help

HELP :wave: this is my first GGW would someone pls tell me which LD is which. I don't want to mess up this expensive LD. btw there are more optics in here than I think my optomitrist owns.

Thanks ! Pyro...
 
dr-ebert

dr-ebert

0
Joined
Mar 8, 2009
Messages
710
Points
0
There's a picture somewhere, I'll see whether I can find it... (the BR is the one in the corner, farther away from the other two).

EDIT: Here and following post.
 
Last edited:
millirad

millirad

0
Joined
Apr 28, 2009
Messages
2,416
Points
63
Glenn, its alive! I am only running it at 122ma, for the moment on my DIY Daedal. I may bump it to 180ma or wait for flex-drive at 180ma. Those short pins on the GGW are scary. I snipped the unused one off carefully and then with 10X magnification carefully soldered positive and negative leads on. If the blob of solder is too large it would be difficult to remove. So I was conservative and then added a little epoxy for mechanical strength. That gold plated base where the pins protrude is tricky because I think you could get shorted to it. I'm hoping that the epoxy plays nice when the LD gets warm. ;-)
 
RA_pierce

RA_pierce

0
Joined
Sep 16, 2007
Messages
3,658
Points
113
Hello scopeguy.
Are you still offering PHR sleds here?
If so, you can PM me for payment details for two.
 
millirad

millirad

0
Joined
Apr 28, 2009
Messages
2,416
Points
63
Glenn, I got my LCC red going nicely at 160ma, but an intermittent connection on the LD terminal killed it. How much for LCC's or equivalent? Just the high power reds. I would like some sent priority if thats available.
 
scopeguy20

scopeguy20

0
Joined
Jun 28, 2007
Messages
3,443
Points
63
Hey Millirad, I have LPC's these are great red LD's and I can ship Priority tomorrow, so it just takes about 2 days usually.

Everyone, I have 11 LPC's and 13 PHR's left, (before millirad's order).
 
millirad

millirad

0
Joined
Apr 28, 2009
Messages
2,416
Points
63
Glenn, I need 2 high power red LD's with 2 Aixis modules. They don't have to be pressed in because I know how to hacksaw the metal piece around the diode now. I'll send you 2 x 12.66 now. Let me know how much for priority shipping thanks. Edit: PM me with the amount and I'll send payment. If those LDs are priced low enough I could use three, with just 2 Aixis.
 
Last edited:
P

palmertech

0
Joined
May 20, 2009
Messages
27
Points
3
Can you put me down for 1 LPCs and 3 PHRs mounted, and one LPC diode with no module? Can I offer $55 shipped?
 
scopeguy20

scopeguy20

0
Joined
Jun 28, 2007
Messages
3,443
Points
63
I am temporarily all out of Axixz modules, may get another batch, and also, I may have a neighbor who would let some go, but for the moment, I just have the following sleds:

PHR's 16

LPC's 9

Thanks -Glenn
 
P

palmertech

0
Joined
May 20, 2009
Messages
27
Points
3
Ah, I see. Would you take an offer of $55 shipped for 3 PHR diodes, and 2 LRC diodes? These need to be removed from the sled myself, yes?
 
Asherz

Asherz

0
Joined
Jan 18, 2009
Messages
1,623
Points
0
How much would it cost to have a LPC pressed into a module and if you happened to have any flex drives lying around have it soldered on and attatched to the correct current? Only my soldering iron broke and I'm left with something that really is not suitable for soldering diode to driver. And shipped to the UK.

Cheers.
 
You must log in or register to reply here.




Top