Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

bluray broblem?!?

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113

In the first picture (0755) you may have bridged the -05 component to the negative wire with either that loose strand or even the main wire if it was bent down that direction in the host

In the picture of the diode (0758), you appear to have solder flowing down onto the remnants of the ribbon board. If the solder flowed under the board or if the board moved down enough to touch the diode case, you will have shorted the diode there.

In all of the shots your excess wire sticking out should be trimmed. ANY of those pieces sticking up could short against the case.

Also, your diode needs to be pressed in further. It should be recessed slightly.

Test the driver as outlined above. Clean up your solder joints. Use flux. Probably, you will be replacing the diode. Remove all remnants of the ribbon cable and board. Insulate the pins with shrink tube and the driver with either shrink tube or tape.

When you re-build. TEST your set-up at EVERY step so you know where it went wrong if it doesn't work.

I test the switch in the host
I test the power leads in the host
I set the driver and double check the current (off/on/off/on/off/on)
I hook up the driver and test it again with the "native" power in the host
I hook up the diode and test it
I heat the shrink tube and test it
I push everything in place and test it
I assemble the entire laser and test it
I focus it and measure the output

No one is perfect. However, by doing that many tests/checks, if it doesn't work along the way, I know where the problem is. I do NOT have to rebuild it to fix it.

Peace,
dave
 
Last edited:





HIMNL9

0
Joined
May 26, 2009
Messages
5,318
Points
0
BTW, for test your dummy load, just get a variable power supply.

Check with the dmm the 1 ohm resistor, for be sure that is not open ..... Connect the dummy load to the power supply, the DMM to the dummy load, and, starting from 2V, slowly increase the output voltage ..... when you arrive just over the diodes dropout voltage, you must start to read on your DMM ..... if so, the dummy load is ok ;)
 
Joined
Feb 5, 2008
Messages
6,252
Points
83
Hot damn, those are one hell of nice macro photos.

Wish I had such optics for my E400...
Anyway, It appears that 'negative' wire from battery to driver is not properly soldered, and it has a little wire sticking out which could cause a short ...

Other than that, I see no missing bits in component, and just follow what dave said...
 
Joined
Jan 8, 2009
Messages
3,145
Points
83
:) nice pics @ OP, and do not listen to lazerboy he is not qualified obviously to give

tech advise on this forum. His eagerness to correct himself was also disappointing.

Good job, Heath ;)
 
Joined
Dec 20, 2009
Messages
64
Points
0
:) nice pics @ OP, and do not listen to lazerboy he is not qualified obviously to give

tech advise on this forum. His eagerness to correct himself was also disappointing.

Good job, Heath ;)
HEY MAN, why would you say somthing like that......how is the advice i gave bad...just because i dint go into detail and made a mistake and corrected myself dosnt mean iam not qualified....sorry for trying to help...and how was correcting myself disappointing.... i never said one bad thing about anything.....I was just trying to help..... SO whats your problem
 
Joined
Jan 8, 2009
Messages
3,145
Points
83
HEY MAN, why would you say somthing like that......how is the advice i gave bad...just because i dint go into detail and made a mistake and corrected myself dosnt mean iam not qualified....sorry for trying to help...and how was correcting myself disappointing.... i never said one bad thing about anything.....I was just trying to help..... SO whats your problem

Hooking an unregulated power source to a diode is a bad senario... if this was taken seriouosly by the OP with a higher priced diode that would have been an injustice to all who have over and over again posted on the proper way to power a diode.:tsk:

EDIT: I have reread your post and I appologize for the severity of my responce. Next time please be more serious and detailed in your posting
on this subject. Nothing worse than having been confused about the issue of directly hooking your diode to a power source to kill your project. Been there done that. jander6442
 
Joined
Jan 23, 2009
Messages
2,113
Points
0
It's ok to help. Just be more carefull when helping out noobs...that's all. Mistakes happen. I would just hate to see a new member be steered away from the laser hobby due to being miss led.
 
Joined
Jan 23, 2009
Messages
2,113
Points
0
It wont happen again...........

Like I said, don't worry about it. People make mistakes, that's what makes us human. It's the people who don't learn from their mistakes, who cause the problems in this world.
 
Joined
Feb 5, 2008
Messages
6,252
Points
83
Nice to see all the guys here eventually ending up in agreeement, not laser war or something ;)

So anyway, OP, did you discover the error?
I hope everything working alright!
 




Top