Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Hello im Fat0panda from Australia

tonyt

tonyt

0
Joined
May 2, 2013
Messages
583
Points
0
SixTee9 said:
Tony, does it stay lazing if you bridge across from the battery to the host without the tail clicky on?
Click to expand...

Nope. As i said, it only flashed on once or twice when i used a piece of metal out of my "dremel kit":p

It flashed on once also when i was putting the cap back on.

But the rest of the time...Nothing. Also i used my dmm to check if there was a current going from the neg battery to the host and there was(around 7.00) but it didn't lase when i did.
 
Last edited:





Laik

Laik

0
Joined
Jan 22, 2013
Messages
946
Points
28
I would try disassembling it and then reassembling it, there is no harm in doing it, it might even work. :)
 
LaZeRz

LaZeRz

0
Joined
Feb 19, 2011
Messages
2,549
Points
63
If you've tried unprotected batts and they aren't the issue, Id bet on a electrical contact issue in the head of the laser. Might be a short or insufficient case path. The issue you're having is similar to one I had with a torch. Cleaning out the threads and tightening everything up might fix it.
 
SixTee9

SixTee9

0
Joined
Jan 26, 2013
Messages
505
Points
0
The driver is a 1.8a from survival laser. I did have one other 1.8a driver go bad and they replaced it for me when I sent it to him but they don't usually do that for drivers. Like I said in email if it is the driver I will buy a new one and a new pill with brass ring and send it to you if you want to put it together or you could send it back and I will fix it for you As I do give six month warrantys on my products
 
tonyt

tonyt

0
Joined
May 2, 2013
Messages
583
Points
0
I only have the once set of protected 18350's until next week.. Also, after disassembling it i have a small round black rubber ring left over i have no idea where it came from!

And cheers sixtee.. I may take you up on that.
 
Last edited:
Laik

Laik

0
Joined
Jan 22, 2013
Messages
946
Points
28
Look on the end of the battery tube, it's probably the o-ring from it. If not, then you got yourself a bonus o-ring :D
 
Last edited:
SixTee9

SixTee9

0
Joined
Jan 26, 2013
Messages
505
Points
0
But I am like LaZeRz I think it is a connectivity problem and I am like him I am thinking that you might want to disassemble the whole clicky switch and then put it back together and making sure it's tight, check the connect continuity between the center stem and outer part of the clicky
 
tonyt

tonyt

0
Joined
May 2, 2013
Messages
583
Points
0
Laik said:
Look on the end of the battery tube, it's probably the o-ring from it. If not, then you got yourself a bonus o-ring :D
Click to expand...

Nah not from there.. Can someone tell me where all the o rings are on a c6?
 
tonyt

tonyt

0
Joined
May 2, 2013
Messages
583
Points
0
SixTee9 said:
But I am like LaZeRz I think it is a connectivity problem and I am like him I am thinking that you might want to disassemble the whole clicky switch and then put it back together and making sure it's tight, check the connect continuity between the center stem and outer part of the clicky
Click to expand...

But if it was just the clicky wouldn't it work when i bridged it? Not just a flash but constantly?
 
Laik

Laik

0
Joined
Jan 22, 2013
Messages
946
Points
28
On all the threads :D The thickest one goes into the retaining ring and stops the heat sink spinning around. Try bridging it again with some tin foil... and wear your glasses ;)
 
Last edited:
SixTee9

SixTee9

0
Joined
Jan 26, 2013
Messages
505
Points
0
There should be an O-ring that's at the face of the Heatsink one behind the 1 inch tube near the pill and one at the tail clicky. I'm not sure if there's one inside detail clicking
 
LaZeRz

LaZeRz

0
Joined
Feb 19, 2011
Messages
2,549
Points
63
I told you to check the switch before I saw that post saying it only briefly flashed. :p

That's why I said clean your contacts and check all connections in the head of the laser.
 
Last edited:
SixTee9

SixTee9

0
Joined
Jan 26, 2013
Messages
505
Points
0
If you scroll up and watch the video I posted on my second post on this thread this page or the page right before it shows how to put the whole thing together and it shows the O-ring placements
 
LaZeRz

LaZeRz

0
Joined
Feb 19, 2011
Messages
2,549
Points
63
Holy crap I accidentally neg repped sixtee9. Someone give him reps. Ill pm a mod about it.
 
You must log in or register to reply here.




Top