anyone know how to get into the focus head part of a "old style" s-ky greenie (group buy) i have the focus head off the laser (undo the pinwrench ring when you fully unfocus it then screw for ages more to get the head off)
but need to adjust the brass internal lens holder thats on a internal...
hey i willl admit to being a bit lazy with this thread making you come to me
but this opens up a idea of you bidding down prices against each other (to my advantage) and i will have a great choice of cases and styles (this will be the deciding factor)
now i know that these diodes can run much...
this is a "good" one of the group buy its got no major faults and the problematic interlock is disabled with a tin plate under the battery plate on the end piece (can be re-enabled in a few seconds with a screwdriver)
the only problem is that if you focus it to the hilt it goes past the...
i have totally gutted a minidorcy ( boost curict and all) and all i have is a plate for the batt + contact with a tab on the other side for connection now what curcit would i need to driver a bluray from the rcr123
i know it will be a boost of around 2-3x voltage and current protection now i...
this is a SOLID laser
i have to say i am very impressed
jayrob himself is a nice guy to buy from
in the package i got:
6 packs of blacktip matches
1 laser
1 dustcap
instructions
2 batts
atm im running it on 3v batts so only getting about 170-200mw but at this power i can run it for around 2...
project: re driver my dx green with my own creation
its a truedx100 (newwish)
but i need to know the approximate current to put into that 808 diode and the driver board from the dx is shot so no readings
i am looking to get 40-50mw out of this green to stop mode hopping issues
the driver must...
i am thinking of building me a cdrw laser 780nm ir from a 52x cdrw and mounting in a axixz for cheaps (have 9 yes 9 of these waiting to be harvested) i expect around 180mw ir anyone have any idea what current i should drive it at with a lm317 driver?
i have decided to remount my dx into a cheap lab laser (mounted in a old cpu block) but i really want to redriver it so anyone know the specs i will need to drive the 808 (ma / v) for this module with analouge or ttl 10-20k
i have potmodded this driver atm and it seems to hang in just fine it...
BUY
a decent spec red diode laser because iv had my hand at them (killed 5 diodes) and cba to build one if you sell it me i want a 6 months garuantee that it wont break from normal use ( 1-2 min on runcycles with whatever off cycle) my float is £50/$100 the lowest wins the sale....
or a trade...
anyone here like fast computers / overclocking if so post your rigs :)
( and benchmark times if possible)
Core2Duo e6750 2.66ghz @ 3.6ghz 1.375v lapped to mirror finish
Crucial Ballistix 6400 @ 900mhz 4-4-4-12 8000Mb/s 2.2v
Msi P35 platinum mainboard rev-b v1.6 bios
Gemini2 with 2 x 220cfm...
i fixed my modehopping issues with a SPOOOON
dxtrue 100
it was pissing me off modehopping ( got a visual with a magnifiing glass at a distance from my wall) it was modehopping bad going into a 01 with no blank space then a hollow line then 3 latitudal areas (02?) and then going dim and...
i am selling a kenom minidorcy ( made by kenom hiself)
iv had my fun with it but need the money :P i am asking $120 shipped to the usa or £55 to the uk
i think kenom is willing to transfer the warranty to you for its remaining time
it is around 145mw ( i think it got tested by senkat on its...
i am sellin 3 homebrew mxdls ( followed deadels guide to the dot :P) at $80 (£40) each (cost + $20) these are mostly for firsttime buyers wanting the "kipkay" for cheap and reliable but not make one themselves
shipping to the usa will be $15 to uk £4
3 to go
1:forsale
2:forsale
3:forsale
i...
this is 2x1gb of Crucial pc5300 (4-4-4-12) DDR2 £28 shipped to uk or $60(£30) shipped to usa/worldwide
background
this is VERY good batch of 5300 its must the highest binned iv found yet but just not good enough for me
i have it stable at 800mhz/5-5-5-15 timing at 2v (stock 1.8v) for 18hours...
i dismantled a aincent projecytor today and have some nice FS morrors some dichromic 50/50 mirrors some colour filters and a rgb thrchromic prism combiner.. dont know what to do ( gona sell eventually) so anyone need any of these??
Full stuff:
1large 2"by4" fs mirror and 2 a smaller 1"by 1 1/2...
Im Thinking of getting a DX green.. should i go for: DX true 100 or DX 150... i have heard the 150 is sometimes not 150 but like 100..
wheras the "trues" are reliable
would someone give a full review of the DX green Range Please??
Post Any Good Hosts You Have Found..
http://www.dealextreme.com/details.dx/sku.4582
this any good? for a miniturised driver (1cm cube)..
made all 3 of my drivers and i am looking for hosts.. before my diodes arrive..
Ideas: 9v square case
2xaa flashlight no lm317 ( just...
i got 2 axixz modules and there filled with a very hard tough epoxy.. i managed to get it apart with 2 huge pliars 1 on each half and the pins of the crap diode ripped with a block of epoxy in the shell so i have the front part just fine iv taken out the diodes BUT i would like the back end for...
just a idea for a board just for posting topics asking for repair help / advice with stickies of common questions/repairs
just to clear the expri/mods and red/green/ir:uv boards of "i broked my laser how i fix"