Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Extend the LPM range with a filter.

I am using the blue filter solely for the 445nm lasers. The few nm deviation of the laser wavelength won't throw off the result much.
 





As mentioned you should verify a filter before you use it for measurements. The best way to do is probably to get a laser that is within the range of your lpm, and take a reading with and without the filter in place.

If you get something like 1000 mW without a filter, you should get 100 mW with the filter in place. Not every filter on the market is entirely linear response, so results may vary from the ideal situation depending on quality.

As for the naming of these filters: ND## filters are usually denoted with ## being the ratio of reduction, wheras OD## filters get labeled with the 10-th power of reduction... for example, OD2 = ND100 at the design wavelength of both filters.

ND stands for 'neutral density' and implies that, for example, a ND10 filter will reduce light tenfold across the entire visible spectrum (i.e. a dark gray filter). In photography such filters are useful if you want to take pictures with limited dept of field under brightly lit conditions.
 
lasersbee said:
http://www.ebay.ca/itm/180701829785?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649

Did you actually test it before recommend it ? Well I have tested the filters. They are unsuitable for this purpose. The blue laser will just burn the filter. It is made of plastic.

burned_filter.jpg
Click to expand...
 
Ouch! That sucks. :undecided:

I think I may know a solution to that.

Why don't you stick the filter close to the LPM and widen the dot by unfocusing it? You still should be able to shine at the sensitive region of the thermophile but not as concentrated that it'll burn out the filter.

Cheers!
 
Or... just use a diffraction grating or piece of glass. Why do you insist on complexity? Am I invisible?
 
Hey guys, would anyone know if the 20% filter of wickedlaser would be suitable for this trick? I want to test my 9mm diode but i guess 2W is not going to be enough :p

Anyway would the whacklaserlens burn out with 2.5W on it? :)

Greetings,,
 
No. Although it is glass, I've melted one with 4W. It'll probably crack with 2.5W
 
Cyparagon said:
Or... just use a diffraction grating or piece of glass. Why do you insist on complexity? Am I invisible?
Click to expand...

I have use glass filters. The large filter in front of the laser is two UV glass screwed together.

 
Hmm... my only question is if the filter combination blocks say 20% light at 200mW, with it do the same with a 2W. :thinking:

Hopefully it stays consistent!

Cheers!
 
Blord said:
lasersbee said:
http://www.ebay.ca/itm/180701829785?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649

Did you actually test it before recommend it ? Well I have tested the filters. They are unsuitable for this purpose. The blue laser will just burn the filter. It is made of plastic.
Click to expand...

Sorry about that... The set of 3 Glass filters that we did our tests
on are no longer available and I grabbed the wrong link.

If the info we need (glass or plastic) is not in the eBay item listing
we usually contact the seller before purchasing.

Here are some Glass ND Filters and even an adjustable one I
found doing a quick eBay Search....

30mm 30 mm ND2 Neutral Density ND 2 Glass Filter Camera | eBay

37 mm 37mm Neutral Density ND4 ND 4 Filter DC DSLR SLR | eBay

30mm 30 mm ND8 Neutral Density ND 8 Glass Filter Camera | eBay

55mm Vari-ND Fader ND2 to ND400 filter 4 Camera lens | eBay



Jerry

You can contact us at any time on our Website: J.BAUER Electronics
Click to expand...
 
Jerry, no problem ! The filters weren't that expensive. I am going to purchase a 5W Ophir LPM in the future. Bluefan don't have time to make one till October.
Until then I am looking for creative ways for more range. I was thinking several layers of smoke glass.
 
ZzMDL.gif


Here. I'll use Paint-CAD. Glass reflects around 10% of light, right? You can therefore increase the sensor's range by 10x if you use the reflected beam from a regular piece of glass.

attachment.php


Since the glass absorbs very little of the beam, this should work for tens of watts.
 

Attachments

  • glass attenuator.png
    glass attenuator.png
    11 KB · Views: 272
Last edited:
Ah, now I understand what you mean. You measured the reflected beam and not the beam though the glass. This will imply other factors in the calculation as well, like the angle of the glass and the consistency of the glass surface. I will try it tonight :)
 
Ahhhh, gotcha Cyparagon. Sorry if we made you frustrated.

I love when people portray their thoughts via GIF's.

But my question still stands: will the reflectivity be consistent for both low powered reflections and high powered beams?

Thanks for the brilliant idea! :beer:
 
Yeah, I suppose the reflection's power will vary slightly with angle, but that goes for ND filters too. Hell, any power measurement will vary with the sensor angle if you wanna get picky. :p

The reflectivity doesn't vary with power though.

You can also use a beam from a diffraction grating in a similar way. Again, they absorb very little of the beam energy. I've had cheap plastic gratings (dirty, even) in the path of a 4W beam and they're just fine.

attachment.php
 

Attachments

  • grating attenuator.png
    grating attenuator.png
    10.7 KB · Views: 260
You must log in or register to reply here.





Back
Top