LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
Where to get a 2.8 resistor
- Thread starter Kulhu
- Start date
- Joined
- Jul 17, 2010
- Messages
- 2,160
- Points
- 0
Fry's would probably have the resistor you want.
I thought so, Thanks!
- Joined
- Jul 17, 2010
- Messages
- 2,160
- Points
- 0
If the store over at I20 is out have them call the I635 store to see if they have it.
LarryDFW
0
- Joined
- Dec 6, 2008
- Messages
- 1,581
- Points
- 63
There are standard values for resistor values.
For 5% tolerance, 2.7 ohms is the closest value.
I don't think you will see any difference between 2.7 & 2.8 ohms.
I have some 1/4 watt 2.7 resistors here in Dallas if that would help.
LarryDFW
Yea, that store is within jogging distance.
- Joined
- Jul 17, 2010
- Messages
- 2,160
- Points
- 0
But as Larry has some You might want to hit Him with a PM
If i can't find them there i will buy his, but i have other items i have to buy there aswell.
Toke
0
- Joined
- Jul 25, 2010
- Messages
- 1,099
- Points
- 0
The standard values of resistors is set by the distance between values at each % of accuracy.
If you go for 1% resistors you can find 2.8 Ohm.
EL-SUPPLY: 1% 2.80 OHM METALFILM MODSTAND
Another solution would be to buy a pack of 100 5% 2.7 Ohms and then go through them with a meter, then verify by testload.
If you go for 1% resistors you can find 2.8 Ohm.
EL-SUPPLY: 1% 2.80 OHM METALFILM MODSTAND
Another solution would be to buy a pack of 100 5% 2.7 Ohms and then go through them with a meter, then verify by testload.
HIMNL9
0
- Joined
- May 26, 2009
- Messages
- 5,318
- Points
- 0
or parallel 2 of them .....
3,3 ohm in parallel with 22 ohm gives 2,86 ohm
3,3 ohm in parallel with 18 ohm gives 2,79 ohm
3,9 ohm in parallel with 10 ohm gives 2,80 ohm
(rounded to 2 decimals)
3,3 ohm in parallel with 22 ohm gives 2,86 ohm
3,3 ohm in parallel with 18 ohm gives 2,79 ohm
3,9 ohm in parallel with 10 ohm gives 2,80 ohm
(rounded to 2 decimals)
Last edited:
- Joined
- Dec 29, 2009
- Messages
- 3,136
- Points
- 63
what HIML9 said. An added benefit of this, since I'm thinking you are probably using the lm317-based driver in CC config, is that if you parallel two 1/4W resistors, the resulting equivalent resistor will be able to handle more power, near 1/2W.
bootdsc
0
- Joined
- Sep 11, 2010
- Messages
- 10
- Points
- 0
radioshack resistors are always a little off so i have found that
4 "10 ohm" resistors gives me 2.8 ohm exactly because the
resistors are closer to 11.5 ohm each. with my lm17 current regulator
set using 2.8ohm i get 860ma(i think,might be 816ma) and nothing gets
vary hot at this current.
HIMNL9
0
- Joined
- May 26, 2009
- Messages
- 5,318
- Points
- 0
HUH ? .....
An LM317 with a Rset of 2,8 ohm must give you around 450mA, not 860 .....
Rset calculation for current is 1,25 (the reference voltage of the IC), divided for the resistance (in ohm), gives you the current (in ampere) ..... so, 1,25 / 2,8 = 0,446A ..... are you sure that your driver is wired correctly ? ..... and that the resistor is effectively 2,8 ohm ? (by the way, never trust to DMM for low resistance precise measures, if you are checking it with them ..... they are not good for this use, you need a specific instrument)
bootdsc
0
- Joined
- Sep 11, 2010
- Messages
- 10
- Points
- 0
yes you are right, i forgot to mention i use two complete lm317 circuits with the 4 resistors on each one..in parallel. giving me a total over 800ma. so far this is my best driver, stays cool and so does the diode heatsink..unlike when its ran at 1200ma off one lm317. that whole setup stays warm even with a fan.
