Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

driver for o-like 9mm

K

kirby

0
Joined
Aug 7, 2010
Messages
21
Points
0
I am currently building a 1w 808nm portable laser. I have everything but a driver. I've seen a few using search but they're all big and I was wondering if any would fit inside the o-like 9mm module, it would be more convenient. So if anyone knows or want to suggest a driver, please post :)

P.S. Before anyone asks, yes I am aware of the dangers of an infrared laser and I do have appropriate goggles.
 





moonreft

moonreft

0
Joined
Sep 1, 2009
Messages
108
Points
0
rkcstr (about thumb nail size) and dr lavas (about middle finger nail size) will fit.

The bigger question is what is your power source?
 
Last edited:
Toke

Toke

0
Joined
Jul 25, 2010
Messages
1,099
Points
0
moonreft said:
rkcstr (about thumb nail size) and dr lavas (about middle finger nail size) will fit.

The bigger question is what is your power source?
Click to expand...

????
Dr lava's drivers are 9x12 mm, a 9mm module is less than 9mm on the inside.
Are you suggesting shaving the edges enough to fit the driver plus insulation from case?
 
moonreft

moonreft

0
Joined
Sep 1, 2009
Messages
108
Points
0
The LM317 will also do. I'm not a big fan but that totally depends on the power source he intends on using.

A fine metal file and a steady hand will do. May need to tape it if he takes off too much.
 
Toke

Toke

0
Joined
Jul 25, 2010
Messages
1,099
Points
0
moonreft said:
The LM317 will also do. I'm not a big fan but that totally depends on the power source he intends on using.

A fine metal file and a steady hand will do. May need to tape it if he takes off too much.
Click to expand...

Ok, both solutions would work.
I were just a bit annoyed that you omitted the "modifications" at first. :)
If it connects to batteries through a spring on the driver he would either have to expand the hole in the endcap, or omit it, saving some grinding down of driver. It will be a little tricky to ensure heat sinking of the driver.
 
SHIN

SHIN

0
Joined
Jul 25, 2009
Messages
207
Points
18
I built my IR laser with the cheap LED driver.

IR LD is can-positive and Vf is about 2V. So this amc7135 driver is a good match.
3 or 4 of amc7135(300-350mA) with one Li-ion battery will work fine.

SHIN
 
K

kirby

0
Joined
Aug 7, 2010
Messages
21
Points
0
SHIN said:
I built my IR laser with the cheap LED driver.

IR LD is can-positive and Vf is about 2V. So this amc7135 driver is a good match.
3 or 4 of amc7135(300-350mA) with one Li-ion battery will work fine.

SHIN
Click to expand...

the amc7135 is 17mm large, will not fit in a 9mm module.
 
SHIN

SHIN

0
Joined
Jul 25, 2009
Messages
207
Points
18
You can cut the amc7135 driver into rectangular shape. (especially 2x amc7135)
I built 500mW 5.6mm 808nm LD in aixiz with 2x amc7135 rectangular board and woked fine.
I think it is possible that 2 of rectangular boards(each has 2x amc7135) can be containable.
Microflex or rkcstr is common in negative, so there is an insulation problem with the host.
It is against the heat-sinking.

SHIN
 
You must log in or register to reply here.




Top