Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Driver with built in duty cycle?

Cube777

Cube777

0
Joined
Jul 22, 2012
Messages
426
Points
28
Hi LPF,

I don't have the knowledge (yet) to design something like this, but what if someone can build the usual driver like a FMT but with a built in timer to switch off the laser after it has reached it's max duty cycle "on" time and keep it off till it has cooled off, thus protecting the laser from n00bs who doesn't know what a duty cycle is. I'm sure someone here could design one, and maybe a adjustable one too? :thanks: for reading!
 
Last edited:





baharini

baharini

0
Joined
Jun 26, 2010
Messages
67
Points
8
What sort of form factor are you looking for? A labby or portable build?.
I have a few ideas and could design one.
 
Last edited:
Cube777

Cube777

0
Joined
Jul 22, 2012
Messages
426
Points
28
i'm thinking this could work for handhelds (labby's won't need this), but I don't have a use for it yet, just throwing around some ideas.
 
Moistenator

Moistenator

0
Joined
Jun 26, 2012
Messages
788
Points
28
It's a good idea. But it's not needed, Noobs who don't understand how to operate a laser and stick to a duty cycle shouldn't be in possession of any lasers above 5mW.
 
Bionic-Badger

Bionic-Badger

0
Joined
Oct 26, 2007
Messages
5,438
Points
83
I dunno... I could just see all the n00bs visiting this forums complaining that their laser is broken because it shuts down periodically while in use.

I also think it would be dangerous to have it turn back on once the laser has sufficiently cooled down. It ought to just shut off completely until turned on if it gets too hot.
 
Cube777

Cube777

0
Joined
Jul 22, 2012
Messages
426
Points
28
We could just add a note when you sell the laser saying "The laser will shut down automatically after X minutes", and I agree it shouldn't turn on automatically, you need to physically turn it off and then on again (after the cool down time is finished). Also the cool off time should only initiate if it had reached it's max "on" time, otherwise it could get complicated and annoying.
 
Bionic-Badger

Bionic-Badger

0
Joined
Oct 26, 2007
Messages
5,438
Points
83
It'd probably be better just to measure the heat and if it overheats, then shut off. Still, such a system wouldn't be worth adding to cheap lasers, and usually people with the better lasers know how to manage their on-time.
 
jArdi

jArdi

0
Joined
Jan 21, 2013
Messages
142
Points
18
How about this:
How About:
2 Switches/Click buttons, 2 LED's, + Laser diode.

Button 1: Turns on power
Led 1: Power Indicator [ON]

Led 2: Indicates Laser Duty cycle has passed, and your laser will now operate.
Button 2. Turns on LD

As the LD is on, led2 will blink. As the LD approaches the max duty cycle, the LD will blink faster or slower (either one, depending on what you want)

OR

Rather then led2 being on and saying your laser is 'armed' it can be like a 'hold' light instead. While led2 is on, you cant use it.
Of course, you can easily bypass this simply turning on/off full power, but then it will be your own fault for wrecking your LD
There are tons of combos you can do with this, all can be very simple.

A note: for anybody who doesnt feel like having 2 led holes drilled, you can easily get a click button with a multicolor light - that will indicate power, hold, armed/ready etc....
 
Cube777

Cube777

0
Joined
Jul 22, 2012
Messages
426
Points
28
^Very good idea..... then your not limited by the duty cycle yet there is protection for it.
 
cheech226

cheech226

0
Joined
Jun 25, 2011
Messages
1,481
Points
63
Who is going to pay an extra $50 (kinda arbitrary figure) to shut their laser off for them? there are greens that will adjust current to the pump to prevent overheating. but i think here we over complicate things for diode lasers
 
Flaminpyro

Flaminpyro

0
Joined
May 4, 2009
Messages
5,443
Points
113
I rather like the idea of a temp sensor that will shut it down when it reaches a certain temp and let it be turned on when the temp drops a certain amount.

Wait a just one second we already have a driver that will do that and it's called a V5 :D
 
jArdi

jArdi

0
Joined
Jan 21, 2013
Messages
142
Points
18
cheech226 said:
Who is going to pay an extra $50 (kinda arbitrary figure) to shut their laser off for them? there are greens that will adjust current to the pump to prevent overheating. but i think here we over complicate things for diode lasers
Click to expand...

for the record, it will only cost like $2, total, MAX.the led is more expensive than the chip.

Flaminpyro said:
I rather like the idea of a temp sensor that will shut it down when it reaches a certain temp and let it be turned on when the temp drops a certain amount.

Wait a just one second we already have a driver that will do that and it's called a V5 :D
Click to expand...

I can implement that.
 
Hiemal

Hiemal

0
Joined
Dec 27, 2011
Messages
1,443
Points
63
Guys you do realize that nearly every driver in existence has some sort or form of thermal protection built into it?

The manufacturers of the IC's know that temperature is obviously something to keep in mind. So they often do us a huge favor by adding in overtemp sensors in the IC itself, so when it gets too hot, it starts to limit itself in some form or another, whether it be by flickering, lowering the output current...

This does the job well enough for you.

HOWEVER

If you're talking about the laser diode itself, that's something completely different...and would be kind of silly to bother implementing. Just feel the heatsink/laser diode area with the palm of your hand. If it's too hot, turn it off. Not hard.
 
You must log in or register to reply here.




Top