Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Osram PLTB450 1.4W 450nm Diodes

DTR

DTR

0
Joined
Jun 24, 2010
Messages
5,683
Points
113
The new PLTB450 diodes are now in stock. This thread can serve as a place for testing and discussion.


Here are the specs from Osram's website.

Product Catalog | Products | OSRAM Opto Semiconductors

Technical Data (at 25 °C)
Output Power: 1.4 W
Emission Wavelength: Typ. 450 nm
Threshold Current: Typ. 0.2 A
Operating Current: Typ. 1.2 A
Efficiency: Typ. 27 %
Package Type: TO56

Here are some of my observations so far.

Here is a comparison. Paced out 30 feet so it could be off by a foot or two either way. Measured the line with my calipers.
p10196601.jpg


Here is a comparison of the raw output. M140 on top.
yd0a.jpg



Ok here are some power measurements with a G-2. These were done without a lot of cool down time so there may be a little higher peaks for the higher currents with active cooling.

1270mW @ 1.2A
hhkr.jpg


1540mW @ 1.4A
tvrj.jpg


1720mW @ 1.6A
lypr.jpg


1830mW @ 1.85A
eod4.jpg
 
Last edited:





The raw output pic sure is interesting, its quite a narrow band of light
 
I'm missing the purpose of this diode? Seems like it's worse than an M140?
 
I though the same thing at first but the beam does look a tad tighter when focused with a lens and if you can see in the first picture the line is about the same length if not a little shorter than the M-series diodes. They certainly are not as powerful as the M-series diodes.

I am not sure if it will prove to be correct and only testing could tell but it has been suggested to me that the tighter stacking of the lines on the Osram may be advantageous to in trying to correct the beam with correction optics.


Here is what I am seeing. I noted the focused line is vertical with the shorter aixiz of the raw output not the long when focused. I would think this is actually more desirable.

newbitmapimage3df.png
 
Last edited:
Interesting DTR, did these come out of a projector or off the shelf?
 
No projector on these yet. They are sourced from the manufacturer.:)
 
interesting!

Do you think the 1.6W versions will be the same beam specs as the M140, the slow axiz will be fatter as they will use a bigger emitter to get the power up?

Also have you put one on the spectrometer? running hot these could make up to 460nm?
 
Last edited:
Fiddy said:
interesting!

Do you think the 1.6W versions will be the same beam specs as the M140, the slow axiz will be fatter as they will use a bigger emitter to get the power up?

Also have you put one on the spectrometer? running hot these could make up to 460nm?
Click to expand...

1W 460nm sounds pretty awesome :D
 
Fiddy said:
interesting!

Do you think the 1.6W versions will be the same beam specs as the M140, the slow axiz will be fatter as they will use a bigger emitter to get the power up?

Also have you put one on the spectrometer? running hot these could make up to 460nm?
Click to expand...

Don't know until we see them. I don't have a spectrometer but they look pretty much the same as the M140's to my eyes.:)

AnthoT said:
1W 460nm sounds pretty awesome :D
Click to expand...

Yes it would.
 
The beam size would probably make these easier to combine too. I think this would be an advantage for prisms correction. The angle of the prisms wouldn't have to be as much, and I found when testing with prisms that the greater than angle, the bigger the power loss.

I'll have to get one of these for my corrected handheld build idea when I have the coin :)
 
Here is a better shot. The M140 was metered @ 2.2W and the PLTB450 is only being driven @ 1A(only driver I had below 1.4A) and measured about 1050mW so that is why it seems fainter.

Paced out 30 feet so it could be off by a foot or two either way. Measured the line with my calipers.:)

p10196601.jpg
 
Oh the first second i thought Output Power: 1.4 W RMS output.


Well to bad it's not much interesting.

Good revieuw tho.
 
0_o

I grabbed one...

DTR's diodes have allway's worked great for me the ones I have killed have been my fault..
 
Though I would share. Built myself a nice little Powerlight unit with one of these diodes and a 1.1A ATMA driver using a three element lens. Does 880mW. I have to say they definitely have a much tighter beam than the M140's. The color difference is not great but you can notice it when they are side by side. I am fond of smaller builds and I will say this is my new unit of choice for daily use.

If you are not after the most powerful unit out there these definitely have some appeal.:D

p1019711.jpg


p1019712.jpg
 
Nice I like the b50 hosts too nice and small.. I havent built mine yet worked on the mits500 tonight will make a post on it soon.. Hope to build the PLTB450 in the next couple day's.
 
You must log in or register to reply here.


Back
Top