Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

500mw 445nm True Blue Diode $470 =)






jayrob

0
Joined
Sep 21, 2007
Messages
9,862
Points
113
I think the detail missing is that "multimode" is a completely relative term. If it's not one, it's multi, and therein lies the possible confusion. It could be gain-guided with some massive width, or it would be what that one guy said on PL and be index-guided and only 7um wide. A 7um ridge laser would likely be multimode, but not nearly as bad as wider ridges, and not nearly as bad as a gain-guided diode.

Then, even beyond the diode, you get into "multimode" bars which are actually multiple emitters, which makes it even worse.

But just someone saying "multimode" could mean any of these things, especially if you get people who just hear "multimode" and really don't know the difference. It's a phrase that gets repeated a lot with relative certainty, even though it is a completely relative term.

If the guy on PL is right and it's an index-guided 7um wide laser, then it's likely not going to be too bad. A single mode laser may be 2 or 3 um wide, just for reference, so 7um isn't that much wider, relatively speaking. ETA: Also for reference, a PHR has a ~1.5um ridge width.

Here's what drlave said about it in another thread:

the beam, as it comes out of a basic aspheric collimator, is about 4.5mm tall and 0.2mm wide. over a distance it turns square, then rectangular reminiscent of a c-mount 808 collimated with the same method. I do know of a few ways to collimate the beam into an even 'dot' namely using cylindrical lenses but have not acquired the proper lenses yet. If I do, there may be a group buy or something so if you buy one of these diodes keep in touch.
 
Joined
Aug 25, 2007
Messages
2,007
Points
63
^After a lens that's already in the far-field, I'm not sure how that translates to diodes size and whatnot. I was just throwing a guess/possible explanation out there based on what one guy said on PL (that it has a 7um width), I have no idea if he's right or not. Just that if he is right, then it likely is somewhat multimode, but certainly nowhere near as bad as many multimode (or even multi-emitter) diodes you've seen in the past.


Even with the PHR and how well known it is, it took a bit of extra work to be able to tell you that it has a 1.5um ridge width and a cavity length of 400um, and not much else. Maybe in a few months I might have some more info to share on it, but not a lot.
 
Joined
Nov 7, 2008
Messages
5,725
Points
0
So would a 7um index-guided 444nm diode be likely to have good enough characteristics that FAC is unnecessary? If so, and these diodes are of that type, that's very good news..
 
Last edited:
Joined
Aug 31, 2009
Messages
2,157
Points
0
I'm already working on a way that will allow multimode diodes to be used in regular hosts like jayrobs.
Need to save up for the parts though. Jayrob I will be contacting you soon about something I need.

EDIT: Don't really care anymore
 
Last edited:
Joined
Oct 24, 2008
Messages
1,057
Points
48
Well if the lens is asymmetric than the typical screw in method wont work will it? The lens or lenses will have to be aligned with the asymmetrical output of the diode.

IMO, even if the diode can output 150mW it'll be a good buy. That is a very rare and exotic wavelength. Even more rare than yellow pointers.

Personally I care more about the wavelength than power output. Burn stuff with 405nm, and set this diode at a VERY conservative power level.

I really hope that blue diodes are manufactured more frequently. TVs are soon going to ditch LED technology and adopt laser technology. Since diodes are more stable, smaller, and more efficent, I think laser TVs will favor diodes over DPSS. Eventually I'd bet DVD burners aren't going to be the only thing we're gutting to make lasers. :)

-Tony
 

Trevor

0
Joined
Jul 17, 2009
Messages
4,386
Points
113
Why do you think this? Laser TV's already exists, but it seems that manufacturers largely goes for OLED's instead.

Laser technology is more expensive; hopefully they'll move from OLED to laser once it is not cost prohibitive.

-Trevor
 

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
Well if the lens is asymmetric than the typical screw in method wont work will it? The lens or lenses will have to be aligned with the asymmetrical output of the diode.

-Tony

The lenses being used and discussed are aspheric, not "asymmetric". Asphereic lenses are what we are mostly already using.

Peace,
dave
 
Joined
Jan 12, 2008
Messages
3,290
Points
83
Laser technology is more expensive; hopefully they'll move from OLED to laser once it is not cost prohibitive.

-Trevor

I don't think one will repalce the other, I bet there will be a ton of uses for OLED aswell for laser TVs.
 

drlava

0
Joined
Mar 7, 2007
Messages
1,152
Points
0
These are pretty exciting diodes. Typically they would cost thousands in low quantities like this. For pointer purposes, they aren't that bad, and will amaze you with how powerful this blue wavelength appears compared to 405nm. I have looked into some FAC solutions, some costing as much as $250. This lens probably won't be worth it for a pointer, but will for a projector. As youall get them, I look forward to hearing your experiences :)

Also, I think they are probably gain guided, not index guided.
 
Last edited:

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
I NEED more than 24 hours in a day. Can anyone help?

Peace,
dave
 
Joined
Jul 4, 2008
Messages
2,499
Points
113
Why do you think this? Laser TV's already exists, but it seems that manufacturers largely goes for OLED's instead.

Not in TVs, but in micro-projectors. SAMSUNG has a prototype that I saw at COEX technology show last year. It uses 1 red, 1green DPSS? Not sure.... and a true blue diode. The total size is a little larger than a deck of cards.
Resolution is still only 800x600.


They are working on 720p and 1080p versions. ---

BTW, I have a micro projector for sale if anyone is interested in it.
It's called a BIT projector. Res is 800x600 in VGA and RGB/XVGA powered by a 5W LED.
 




Top