Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Tesla Coil Build Thread

Joined
Dec 11, 2011
Messages
4,364
Points
83
Regarding raising the topload up off of the secondary, this actually causes more stress on the secondary and can cause several issues with performance and longevity if it is lifted too high in regards to the top winding. It helps reduce eddy current losses in the topload to raise it, but really there's no gain beyond that and there are better ways to eliminate topload eddy currents.
 





Joined
Dec 11, 2011
Messages
4,364
Points
83
I got some more work in today on my big coil's rebuild. This was towards the end of the session, but the bridge and controller are finished now. I just need to make up the LV transformer's power cable and make/attach the resonator's primary.

bhH6kML.jpg



Also, this happened:
dyhGV1l.jpg
 
Last edited:
Joined
Jan 14, 2009
Messages
1,452
Points
83
Nice : D ,


Heh been there loads of times , the one place I miss is the one place the iron wont reach without melting something ......
 
Joined
Jan 14, 2009
Messages
1,452
Points
83
Mini 10Kv 10mA HV transformer that I'm putting in a 1L pain can under oil , with HV rectifier to use as a HV DC supply , 100M resistor is used to run a 100uA HV meter with 10Kv Scale .

Unit is sealant sealed and glands are sealed as well to give an air tight setup

P1000048 by TwirlyWhirly555, on Flickr
 
Joined
Jan 14, 2009
Messages
1,452
Points
83
Thanks , but unfortunately that transformer was a flop , didn't work very well , So I now have two 25mA 10Kv NSTs .

I do have a question , I made a marx with 12 stages and 2Mohm resistors / input resistor is alos 2Mohm on the positive side
I made a DC rectifier for the NST using 8 4Kv 250mA diodes per string ( 32Kv Peak revers rated total )

This was then potted in wax , but after about 8 shots of the marx one string whent short :/

I'm not sure if this was over voltage or not , it dosent seem it could be current related , even with 2Mohm input on the marx supply current shoundt go past 5mA but there is no 2Mohm resistor on the negative return so that may be the problem ?
 
Last edited:
Joined
Jan 14, 2009
Messages
1,452
Points
83
Did you tie the rectified negative line to ground?

I haven't , No

The transformers still has the ground fault protection , so wouldn't doing that cause it to trip ?


Edit : I have looked around online and didn't find any mention of trying the rectifier negative to case ground but I did see people using large input resistors to the Marx - 5-25Mohm .

Edit 2 - rebuilt it with 4Mohm on the positive side , 2Mohm on the negative and its working with it firing every 2 seconds or so @ 10Kv in

Edit 3 - Yup :D , 11cm Spark


P1000094 by TwirlyWhirly555, on Flickr

P1000095 by TwirlyWhirly555, on Flickr
 
Last edited:

upaa27

0
Joined
Jul 10, 2013
Messages
618
Points
28
Hi guys!

Here is my DRSSTC. CM600 full bridge. Slightly modified UD 1.3b. Photos are 340V on the bridge, around 500A primary current, 240bps and 190us on time. It makes 4-5 feet of spark until I redo my bus cap configuration.

9WgCNVL.jpg

2acwKPw.jpg


Thanks for looking!
 
Last edited:

upaa27

0
Joined
Jul 10, 2013
Messages
618
Points
28
Very nice! What controller are you using?

Thanks! I am using Steve's UD 1.3b. Unfortunately, without phase lead I am switching about 70 degrees too late! Nasty spikes on the bridge output!
 
Last edited:
Joined
Dec 11, 2011
Messages
4,364
Points
83
IIRC phase lead is easy to add though. Check 4hv for specifics. I think it's just an inductor and maybe another supporting passive.
 
  • Like
Reactions: ped

upaa27

0
Joined
Jul 10, 2013
Messages
618
Points
28
IIRC phase lead is easy to add though. Check 4hv for specifics. I think it's just an inductor and maybe another supporting passive.

I did try that, it didn't do much though. The 7414 has too wide a hysteresis band(it did work for some people though) so the newer drivers use a comparator. Hmm... :thinking:
 
Last edited:
  • Like
Reactions: ped




Top