Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

The REAL Kryton GB round #3. Taking payments now.






viperx1101

viperx1101

0
Joined
May 6, 2010
Messages
427
Points
18
Icecruncher...I can't help myself from staring at your avatar...I want what you have...

And hopefully soon I will have it!!!
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Yeah you can still get in on the beasts and the grooves. I am still negotiating the beasts so I honestly haven't got an accurate time frame. I ABSOLUTELY HATE to leave folks in limbo like this and if we can't make some headway soon, I'm going to start refunding money...

I will state this. REGARDLESS THESE BEASTS WILL BE REALIZED! I will not abandon them.
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
run into one more issue. Apparently, I need to get a flow through system for my vibratory polisher. The aluminum dust that is building up inside the polisher is making it so that the media isn't getting polished. it's creating a buffer so that it's not polishing. The polisher I've got hasn't got a sealed bowl so I'm going to have to make it sealed with silicone or buy a new bowl (in the vascinity of $190) and then buy a pump and some tubes as well as some chemicals to pull the dust off the media and dump it in a bucket as it polishes. ($60)
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Looks like I might have this solved. I have done some modifications to the polisher that may work in allowing me to use this as a flow through system. I will test it tomorrow and report.

I still need to buy the chemical to flush the gunk out while it's polishing, but the mod was relatively inexpensive.
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Extrion was nice enough to sand blast the few that needed them. Here they are

05ba3fda.jpg

9b3e47f3.jpg

953528d5.jpg
 
exquzmwa

exquzmwa

0
Joined
Feb 4, 2011
Messages
6
Points
0
Thanks Kenom :paypal: Please advise if I should put it in the spreadsheet also. I didn't see any beasts listed (at least named) in the SS and wasn't positive what each of the columns are intended for (i.e. not 100% postive if Col F is intended for the Beasts).

:beer:
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
it was intended for the beast but that's why I specified in the payments that it be in a specific format cause folks keep messing with the spreadsheet. I have the specifics in the payment so I can always go back and refer to that.. so updating the spreadsheet isn't necessary.
 
jakeGT

jakeGT

0
Joined
Oct 29, 2010
Messages
3,532
Points
0
I have no idea if this has been posted, 43 pages... haha

But, do you have an idea of when these will be available? and when would I have to have my payment in to meet the deadline, I want one, but would like to wait a week or two before I paid if that is okay.
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
it is my hope to have these finished by the end of next month. I have the anodize setup all ready to go, and as soon as I get a good finish on all these barrels, I will start anodizing. Now let me state, just because the anodizing is done, does NOT mean these will ship. They will then get sent to a Laser engraver to have the logo laser engraved onto the barrels.

DSC00509.jpg

DSC00375.jpg


You have plenty of time to get on board.
 
Last edited:
AJ_Dual

AJ_Dual

0
Joined
Aug 10, 2007
Messages
526
Points
0
Oh GAWD! I forgot ALL about the laser engraving of the logo... DROOOOOOOL!

I've got a source for some blue rubber cord to put in the grooves. It's going to look just absolutely sick!

(chortle)
 
You must log in or register to reply here.




Top