Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Laser Barrels V2. GB. Second run. Kryton Groove

Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Re: Laser Barrels V2. GB. Second run. Kryton Groov

daguin said:
[quote author=BluRay link=1204788577/1260#1261 date=1224410740]Ken i have a question.
Since the Groove Driver didnt come with any instructions, and i looked up the last post you showed me on how to add the springs to the  board, to see which end is the Power input and which is the output to the diode.
My question is, With the spring  touching the Possitive of the battery, how do you connect the Neg to the barrel?? to you just wire it so its just touching the barrel? or is there aomthing else?
Tommy
Click to expand...

Just solder the negative pin and the case pin on the diode together.  Bend the case pin over so that it touches the negative pin and solder your negative contact on the driver to both.  You could also just allow the solder on the negative pin to flow down onto the diode, but I try to keep the diode as cool as possible.  The negative comes through the barrel that way.

Peace,
dave[/quote]

Yeah what he said. It really is the best option to short the diode case to neg as it completes the circuit through the case. There are assembly instructions and I've posted them in this thread SOMEWHERE!! lol I'll post the link to the assembly instructions for the driver again.

http://hacylon.case.edu/laser/lavadrive1/Assembly_Instructions.pdf
 





B

BluRay

0
Joined
Jul 4, 2008
Messages
591
Points
0
Re: Laser Barrels V2. GB. Second run. Kryton Groov

So, because the diode ha only to pins left. your saying solder the neg to the neg bit of the driver where the diode neg pin is suppose to touch, and make the solder touch the neg part of the pcb board to the yellow bit on the diode case?


Ken your link doesnt open for some reason.


Thanks for the info



Tommy
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Re: Laser Barrels V2. GB. Second run. Kryton Groov

BluRay said:
So, because the diode ha only to pins left. your saying solder the neg to the neg bit of the driver where the diode neg pin is suppose to touch, and make the solder touch the neg part of the pcb board to the yellow bit on the diode case?


Ken your link doesnt open for some reason.


Thanks for the info



Tommy
Click to expand...

Ok the link probably doesn't work because you dont' have adobe acrobat installed.  

As far as the diode is concerned I've taken a picture of how I do mine.  You'll see I end up bending the case pin which has no black ring at the base over to physically make contact with the negative pin.  Then when I solder the pins to the driver I also solder the case pin to the negative.
This makes it so that the connection to the negative also makes connection to the casing of the diode itself and can ground out on the barrel which is negative connection.
 

Attachments

  • Image_002.jpg
    Image_002.jpg
    15.2 KB · Views: 80
S

stealle

0
Joined
Sep 27, 2008
Messages
39
Points
0
Re: Laser Barrels V2. GB. Second run. Kryton Groov

It opened for me. If it doesn't for you maybe try right clicking on the link and selecting open.
 
marks47

marks47

0
Joined
Sep 18, 2007
Messages
114
Points
0
Re: Laser Barrels V2. GB. Second run. Kryton Groov

ok that previous post from bluray answered one of my questions... it's a Groove Driver?

How are you guys connecting the + lead to the driver circuit?   I just received mine and am a little behind the times on putting these together...

I'm thinking of finding a throwaway toy or device with a spring in it and trying to find a way to jam it in the top somewhere...
 
B

BluRay

0
Joined
Jul 4, 2008
Messages
591
Points
0
Re: Laser Barrels V2. GB. Second run. Kryton Groov

Ok the link probably doesn't work because you dont' have adobe acrobat installed.

As far as the diode is concerned I've taken a picture of how I do mine. You'll see I end up bending the case pin which has no black ring at the base over to physically make contact with the negative pin. Then when I solder the pins to the driver I also solder the case pin to the negative.
This makes it so that the connection to the negative also makes connection to the casing of the diode itself and can ground out on the barrel which is negative connection.



Okay, that helps, but how about in the case where i've cut my case pin off. cause i was told you dont need them.
Do i then just solder the Neg pin anywhere onto the barrel to ground it? or should i find a smaller spring and solder it onto the Neg end of the driver where the NEG input to the battery goes so it touches the barrel like some of the green laser pen drivers??



Tommy
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Re: Laser Barrels V2. GB. Second run. Kryton Groov

marks47 said:
ok that previous post from bluray answered one of my questions... it's a Groove Driver?

How are you guys connecting the + lead to the driver circuit?   I just received mine and am a little behind the times on putting these together...

I'm thinking of finding a throwaway toy or device with a spring in it and trying to find a way to jam it in the top somewhere...
Click to expand...

What I usually do with the spring is find a old pen that I don't need and pull the spring from it.  sand down the coating around it and solder it directly to the positive connection on the driver.
That or head to your local ace hardware and buy a spring there.  they are usually $.45.  You'll of course want to stretch out the spring a bit to make it go from the driver to the positive connection on your battery.  Here is an example someone else did.  it's a flexdrive but you still get the idea.
*note the additional spring off to the side is NOT Necessary.*
IMG_0157.jpg


BluRay said:
Okay, that helps, but how about in the case where i've cut my case pin off. cause i was told you dont need them.
Do i then just solder the Neg pin anywhere onto the barrel to ground it? or should i find a smaller spring and solder it onto the Neg end of the driver where the NEG input to the battery goes so it touches the barrel like some of the green laser pen drivers??



Tommy
Click to expand...

From there I'd say just make a large blob of solder from the negative pin to the diode casing then.  That will essentially do the same thing.
 
marks47

marks47

0
Joined
Sep 18, 2007
Messages
114
Points
0
Re: Laser Barrels V2. GB. Second run. Kryton Groov

Thanks for the tip. I don't know why I didn't think of the pen spring. I went and bought an $8 mag-lite to LED clicky conversion kit... It looked like the clicky would fit in the head of the barrel with just enough room to spare for a wire coming back up... probably would have been a mess.
Getting the diode into the head, i'm not too worried about.. I found the cable stop you told me about... it's getting it OUT of the Aixiz hosts. I have yet to remove one without SEVERELY damaging the diode. I've used dowels and chopsticks, attempted needles to get into those tiny tiny little holes... no luck.
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Re: Laser Barrels V2. GB. Second run. Kryton Groov

marks47 said:
Thanks for the tip. I don't know why I didn't think of the pen spring. I went and bought an $8  mag-lite to LED clicky conversion kit...  It looked like the clicky would fit in the head of the barrel with just enough room to spare for a wire coming back up... probably would have been a mess.
Getting the diode into the head, i'm not too worried about.. I found the cable stop you told me about... it's getting it OUT of the Aixiz hosts. I have yet to remove one without SEVERELY damaging the diode. I've used dowels and chopsticks, attempted needles to get into those tiny tiny little holes... no luck.
Click to expand...

Use an antenna. LOL you'll find a section of antenna that is the correct size that will fit around the can and viola!
 
pwnstar

pwnstar

0
Joined
Sep 12, 2007
Messages
712
Points
0
Re: Laser Barrels V2. GB. Second run. Kryton Groov

Kenom said:
Use an antenna.  LOL  you'll find a section of antenna that is the correct size that will fit around the can and viola!
Click to expand...

An antenna is a perfect idea. lol thanks.
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Re: Laser Barrels V2. GB. Second run. Kryton Groov

More good news folks. I got in another shipment of barrels today. So, I'll be shipping out some more orders as I organize them into what's owed to whom. I'll also take some pictures a little later of what I've got.

I've also got one or two barrels that are ooops's and will be putting those up for sale here very soon as well.
Ken
 
john_lawson

john_lawson

0
Joined
Feb 22, 2008
Messages
3,182
Points
48
Re: Laser Barrels V2. GB. Second run. Kryton Groov

Hey ken i have a friend who ordered a couple black ones any info on those  ;D


ok ok its me i cant help it i want a oompa loompa now daddy

whow flashback  ;)
 
daguin

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
Re: Laser Barrels V2. GB. Second run. Kryton Groov

Kenom said:
More good news folks.  I got in another shipment of barrels today.  So, I'll be shipping out some more orders as I organize them into what's owed to whom.  I'll also take some pictures a little later of what I've got.  

I've also got one or two barrels that are ooops's and will be putting those up for sale here very soon as well.
Ken
Click to expand...


**poises fingers above keyboard**

**waits**
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Re: Laser Barrels V2. GB. Second run. Kryton Groov

LOL so should I just ask for payment from ya Dave since you'll probably be the one buying them? LMAO!!
 
john_lawson

john_lawson

0
Joined
Feb 22, 2008
Messages
3,182
Points
48
Re: Laser Barrels V2. GB. Second run. Kryton Groov

hey ken why dont ya put that kryton prototype for sale i'd love to see that bidding war :eek:
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
Re: Laser Barrels V2. GB. Second run. Kryton Groov

john_lawson said:
hey ken why dont ya put that kryton prototype for sale i'd love to see that bidding war :eek:
Click to expand...

There's no way that I'd get anywhere near what it's worth. Doggone thing cost me $900 and it looks like crap. I have it setup as a 300mw red and is kind of a "this is where I came from" kinda thing.
 
You must log in or register to reply here.




Top