Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

`jetlasers gb #4 is now CLOSED our $$ is in China






Joined
Apr 2, 2009
Messages
10,662
Points
113
Remember, this laser is going to cost you money.
^^ DJNY wrote in reply to trever22(now banned) and his trolling my thread and conning several here(thus the perma ban(i hope))

good riddence!

DLMB has not had the best luck the post few yrs and the last thing he needed was a scam of his $$.
Good luck in the future Dustin.

***********************************
here are the metering shots for madog's Pl-C 532/600

and Corbins (CDHDC) Pl-C 532/500

you wont see my PL-C 532/400 cause it wasnt done- so much for me getting special treatmernt from JETL--boo hoo :-( he can make nice on my PL-G cost.

these were done several time with mostly very little change ( once I changed batteries in my meter and one of the lasers, Both in perfect shape- foucs is set nicely amd moves smoothly with not too much turning (some of the first PL-C were too stiff and one was too loose but Gray has always made things right aand quickly.

I am doing some outdoor pics in a bit but wont post them til Sat

see combined 1.75W+ of JETL 532. and >3 watts of all nms in last shot.

I ask that all put on thier glasses before enlarging my thumbnails. They both BTW burnt many new scars around the front of my meters and I HAD to wear my glasses= Instaburners.

BE CAREFUL GUYS

keep these stored w/ batt out and keys elsewhere.

you both get free batteries- go eat some cereal.

hak
 

Attachments

  • -ca5io internal optics- tools FS- metering Madog and Corbin 028 (Medium).jpg
    -ca5io internal optics- tools FS- metering Madog and Corbin 028 (Medium).jpg
    56 KB · Views: 88
  • -ca5io internal optics- tools FS- metering Madog and Corbin 031 (Medium).jpg
    -ca5io internal optics- tools FS- metering Madog and Corbin 031 (Medium).jpg
    64.1 KB · Views: 79
  • -ca5io internal optics- tools FS- metering Madog and Corbin 032 (Medium).jpg
    -ca5io internal optics- tools FS- metering Madog and Corbin 032 (Medium).jpg
    60.2 KB · Views: 84
  • -ca5io internal optics- tools FS- metering Madog and Corbin 039 (Medium).jpg
    -ca5io internal optics- tools FS- metering Madog and Corbin 039 (Medium).jpg
    60.1 KB · Views: 84
  • -ca5io internal optics- tools FS- metering Madog and Corbin 047 (Medium).jpg
    -ca5io internal optics- tools FS- metering Madog and Corbin 047 (Medium).jpg
    56.4 KB · Views: 78
  • -ca5io internal optics- tools FS- metering Madog and Corbin 054 (Medium).jpg
    -ca5io internal optics- tools FS- metering Madog and Corbin 054 (Medium).jpg
    58.4 KB · Views: 77
Last edited:

CDHDC

0
Joined
Dec 3, 2009
Messages
248
Points
18
Awesome! I can't wait for it to show up:drool: I'm patiently waiting in the front window with my dog for the delivery man to show up. Wait, what's that!? Oh never mind. It was just the neighbor driving by:whistle:
 
Joined
Apr 2, 2009
Messages
10,662
Points
113
some gratitous nite shots -very poor ones too.

well after 2:30 am still about 80 degrees -very humid and tons of mosquitos.

The green to the right is Madogs 600/532 next is Corbins 500/532 and the one on the left is my 300/532. All JETLASERS.

the 445s are DTR built 800 and 500 mWs. The red is barely visable once the camera adjusts to the Green and Blue. but it is 348mWs of PL-C JETL 660nm/250.

It was a very clear night -no fog or dust in the air.

I will try again with some other lasers-the 600 and 500 are on the way to the new homes--ENJOY!!

My not-so-hot DIY Beam Expander is on Madogs 600-its a bit top heavy and takes two hands to handle-(a whopper) the 'throw' shot is off my new mobile laser lab.
 

Attachments

  • maddog and corbin and frieds 016.jpg
    maddog and corbin and frieds 016.jpg
    32.4 KB · Views: 87
  • maddog and corbin and frieds 015.jpg
    maddog and corbin and frieds 015.jpg
    30 KB · Views: 82
  • maddog and corbin and frieds 007.jpg
    maddog and corbin and frieds 007.jpg
    43.9 KB · Views: 89
  • maddog and corbin and frieds 001.jpg
    maddog and corbin and frieds 001.jpg
    75.1 KB · Views: 76

CDHDC

0
Joined
Dec 3, 2009
Messages
248
Points
18
Nothing like checking your tracking number first thing in the morning to see that it is out for delivery, only to not have your package show up. Ughhhh:cryyy:
 
Joined
Nov 4, 2010
Messages
404
Points
18
So when is GB#5 Im in for a 600mW/532nm hopfully if i can afford it at the time
 
Last edited:

DJNY

0
Joined
Nov 2, 2009
Messages
5,991
Points
83
Do we have a GB price on the Ti-B and the PL-D yet?

Thanks.
 
Joined
Apr 2, 2009
Messages
10,662
Points
113
^^^ yes- sending you the Tracking number now- finally- last two units for this GB- yours and mine!

Feeler thread is started(not my idea--lol) for JETLASERS GB#5.
 
Joined
Apr 2, 2009
Messages
10,662
Points
113
The last two units from this GB arrived today- it took longer than usual but I would much rather wait and get good lasers.

Here are the metering pics for Andrews Ti Pen.
It came with an extension tube that allows the use of aaa primaries , however at 3.0vdc they do not keep up with a 4.2 vdc 10440. I did not have new AAAs so my test for them is not accurate and I will wait allow Andrew to do a proper review when he gets his laser in hand.

Ti pen,250nm/200mWs-- w/ keys-momentary side clicky.
Highest peak was higher than pic show- (one hand on clicky and the other on my camera- didnot catch the peak of 235mWs) For a one minute test the power never dropped below 210mWs.
 

Attachments

  • Andrews(Whodunit) JETL TI 250nm 200mW GB #4 001.jpg
    Andrews(Whodunit) JETL TI 250nm 200mW GB #4 001.jpg
    54.2 KB · Views: 73
  • Andrews(Whodunit) JETL TI 250nm 200mW GB #4 002.jpg
    Andrews(Whodunit) JETL TI 250nm 200mW GB #4 002.jpg
    60.5 KB · Views: 68
  • Andrews(Whodunit) JETL TI 250nm 200mW GB #4 003.jpg
    Andrews(Whodunit) JETL TI 250nm 200mW GB #4 003.jpg
    66.2 KB · Views: 68
  • Andrews(Whodunit) JETL TI 250nm 200mW GB #4 004.jpg
    Andrews(Whodunit) JETL TI 250nm 200mW GB #4 004.jpg
    66.9 KB · Views: 65
Joined
Apr 2, 2009
Messages
10,662
Points
113
Nothing new to report.Subscribe to the feeler thread ofr GB#5 as it will turn into the GB thread after we let it run a while. Not sense doing a GB for less than 10 takers.

and I think you mean the new PL-G or is there a D as well.

I think the problem as I understand it -the Ti series cost a lot to have made Especially the first one. So JETL is wanting to stock the favs so as to not have to have a large inventory of choices. They really something - in your hand it feels like some kind of jewelry I have two and have sold and inspected several more.

Many have aleady gotten PL-C lasers from JETL but I am not sure alll have seen this. There have been some changes for the good since this came out and also a new pin for the tailcap that looks much nicer. The returned PL-C 405 are 500s and now nicely overspec at 600mWs and I have one new FS as well as new Pl-C 250/532. PM for moar details.

Aryntha has 10 days to claim his new 500/532 PL-C 700+mWs or it goes up FS then.
 

Attachments

  • PLC-ENGLISH.pdf
    855.7 KB · Views: 264
Last edited:

mikzip

0
Joined
Feb 3, 2011
Messages
73
Points
0
Now i finally got all the things i ordered in this GB. :san:
Had to wait long to get it all.
Will just share how outstanding Gray has been with me.

I received my 1000mv blue and 600mv green along with a 10xBE about august 15.
I started out frying the Green by mistake putting in the batteries from the blue :yabbem:
I sent it back to china to get it fixed, expected to pay for repair, but he never charged me for the trouble and even sent it back free of charge :). It was ready in a week or so after he received it, but I choose to wait for the red 635nm, 400mv I had set my eyes on as well.

Just received the repaired green and the red yesterday.
The green seems very stable ad peaks at nearly 700mv.
The red also stable and peaks about 425, but really bad divergence, worse than anticipated, makes a square about a meter wide on about 100 meter, so not a pointer but a nice and visibly beam.
My Blue in pl-d host I rarely use because it takes me several minutes to turn it on.
It peaks just a little over 1000.

I haven't been playing with the BE yet, but got adapters for all 3 so I can have them permanently in place. :D

Will hopefully soon be writing some reviews, sorry for the long post :)
All pover testing was done with the supplied batteries. :beer:
 
Last edited:




Top