Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

GB: 4$ heatsinks, 1.5$ aluminum modules AND more!

Joined
Oct 14, 2011
Messages
2,369
Points
83
No problem! Your like the best GB hoster i know so i dont care compensating you with shipping for the new sinks!

You are doing a great job on this and its a shame you made a loss on this. You should be compensated for your effort here!

Thank YOU! :beer:
 
Last edited:





AnthoT

0
Joined
Jan 14, 2012
Messages
2,133
Points
48
No problem! Your like the best GB hoster i know so i dont care compensating you with shipping for the new sinks!

You are doing a great job on this and its a shame you made a loss on this. You should be compensated for your effort here!

Thank YOU! :beer:

Thanks for your support :) I'm trying my best :)

I think if I order 30 replacements it should cover it, someone please correct me if it's too little, I don't want to order more then needed.
 
Joined
Feb 7, 2012
Messages
977
Points
0
Hey 10mins on a drill on the henkel sharpening stones and walla!! here it is.. Only problem was I didnt have a set screw so I used a slightly smaller bit wrapped with electrical tape so I ended up rounding one end a little more than the other but it will work fine now in even my smallest host. Yeah I took it to 8000 grit.


IMG_4375 by Kizdawg, on Flickr


IMG_4376 by Kizdawg, on Flickr
 
Joined
Feb 7, 2012
Messages
977
Points
0
Yep. Sorry Yes I used Blords method as best I could. Mounted it on a drill bit with electrical tape wrap to make it tight because I couldnt find a set screw that would work from other sinks and I just cant cut a slot in one dont have anything that small. I guess my set of 500$ sharpening stones helped.. 250gr, 1000gr, 3000gr and 8000gr I actually wore the 250 down a bit and the back end ended up being .1mm out in about a 3mm lengh so I rounded it a bit butno one is going to see it inside a host anyway...
 
Last edited:
Joined
Feb 7, 2012
Messages
977
Points
0
Three more to go... Eh this isnt that bad at all. I think I can just go slower and almost custom fit them to each host.. It's harder with the fit through the threads heatsink to get a good fit anyway's.
 

AnthoT

0
Joined
Jan 14, 2012
Messages
2,133
Points
48
Three more to go... Eh this isnt that bad at all. I think I can just go slower and almost custom fit them to each host.. It's harder with the fit through the threads heatsink to get a good fit anyway's.

Like I said multiple times 0.1mm isn't too bad at all to sand ;)
:gj: sanding it also Kizdawg
 
Joined
Feb 7, 2012
Messages
977
Points
0
by hand 45min or more. on the drill 10mins polished to 8000grit... and unless you have the OUT OF SPACE version of the auraura with the sky lights no one will ever see the heatsink and the pollished coppers look good.
 

AnthoT

0
Joined
Jan 14, 2012
Messages
2,133
Points
48
by hand 45min or more. on the drill 10mins polished to 8000grit... and unless you have the OUT OF SPACE version of the auraura with the sky lights no one will ever see the heatsink and the pollished coppers look good.

Good work again :) & thanks for all your contributions to this GB, you've helped a lot ;)
 

benmwv

0
Joined
Sep 10, 2010
Messages
1,380
Points
48
I haven't even ordered my sh-032s yet so I'm sure I'll get the new ones :p

I'm happy to pay the shipping for the new version sinks.
 




Top