- Joined
- Jan 1, 2012
- Messages
- 462
- Points
- 18
Mine are the modules. 
Yeah dont worry it was probably just my lens threads, not your modules!
LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
GB: 2$ copper modules ALL SIZES CLOSED
- Thread starter AnthoT
- Start date
AnthoT
0
- Joined
- Jan 14, 2012
- Messages
- 2,133
- Points
- 48
Yeah dont worry it was probably just my lens threads, not your modules!
I tested each before sending them anyway & I didn't have that problem on any of them... Maybe my lens is loose but I know every one screwed on properly :beer:
Please check your PM'sMine are the modules.
Last edited:
- Joined
- Dec 27, 2011
- Messages
- 2,062
- Points
- 48
Which tap do we need for these. It would solve Joe's problem and I need one for an old module that I buggered up the front of when pressing in the module.
I checked on Amazon for 9mm 0.5 tap
Can someone point us to the right tap to chase the threads?
Thanks!
P.S. MJ, that would be your best bet right now. Just get a tap and chase the threads. You could probably even sell it here after you used it and get most of your $ back...
I've heard that about you AnthoT.
I checked on Amazon for 9mm 0.5 tap
Can someone point us to the right tap to chase the threads?
Thanks!
P.S. MJ, that would be your best bet right now. Just get a tap and chase the threads. You could probably even sell it here after you used it and get most of your $ back...
I've heard that about you AnthoT.
Last edited:
AnthoT
0
- Joined
- Jan 14, 2012
- Messages
- 2,133
- Points
- 48
Any 9mm .5 tap would work
BTW tseele this one should be good http://www.amazon.com/Metric-Right-...ref=sr_1_4?s=hi&ie=UTF8&qid=1337823115&sr=1-4
lol I don't get it
BTW tseele this one should be good http://www.amazon.com/Metric-Right-...ref=sr_1_4?s=hi&ie=UTF8&qid=1337823115&sr=1-4
I've heard that about you AnthoT.
lol I don't get it
Last edited:
- Joined
- Jan 1, 2012
- Messages
- 462
- Points
- 18
I have a tap at work I will try tomorrow. Unfortunately I already pressed two 445s into two bad modules.
AnthoT
0
- Joined
- Jan 14, 2012
- Messages
- 2,133
- Points
- 48
I've got extra 5.6mm, I'll send you the amount of faulty ones :beer:
- Joined
- Dec 27, 2011
- Messages
- 2,062
- Points
- 48
If this will work, I can order a set of five and send one to M Joe...
Irwin Hanson Tap 5-0 9MM Plug (Pack of 5)
Irwin Hanson Tap 5-0 9MM Plug (Pack of 5)
Last edited:
AnthoT
0
- Joined
- Jan 14, 2012
- Messages
- 2,133
- Points
- 48
It's .5 pitch not 5... I posted a link for the one that would work
- Joined
- Dec 27, 2011
- Messages
- 2,062
- Points
- 48
Yeah, it just has to come from China. I was hoping the Irwin Hanson Tap 5-0 9MM Plug (Pack of 5) was the same thing. It was prime shipping.
Sorry, attempt at humor. It just sounded funny when you said, "Maybe my lens is loose." Kind of like The Office "That's what she said."
I guess it wasn't funny though.
Well this has been no fun. I have to order a weird sized tap from China and Joe has to get his own.
AnthoT
0
- Joined
- Jan 14, 2012
- Messages
- 2,133
- Points
- 48
Yeah, it just has to come from China. I was hoping the Irwin Hanson Tap 5-0 9MM Plug (Pack of 5) was the same thing. It was prime shipping.
Sorry, attempt at humor. It just sounded funny when you said, "Maybe my lens is loose." Kind of like The Office "That's what she said."
I guess it wasn't funny though.
Well this has been no fun. I have to order a weird sized tap from China and Joe has to get his own.
Lol oh
Joe said he has taps at his work
if he can't fix it I'll sender replacing his, are any of yours defective, I'll replace if I have enough
- Joined
- Dec 27, 2011
- Messages
- 2,062
- Points
- 48
Lol oh
Joe said he has taps at his work
I dont think any of mine are, I haven't checked them all. But I did mess up an Aixiz copper a while back while pressing in a diode, so I want to chase the threads on that one. Plus it would be nice just to have one around to chase the threads on a module if I ever need to do it.
AnthoT
0
- Joined
- Jan 14, 2012
- Messages
- 2,133
- Points
- 48
I'll look into some north American sources for you :beer:
DTR
0
- Joined
- Jun 24, 2010
- Messages
- 5,684
- Points
- 113
I just tried a bunch I have sitting here and found a few that got tight but I found if as soon as you feel it getting tight then back it out and back in a few times it will loosen up but if you try to power through it they will bind up. Might be burs on the threads. We should probably ask in future batches they run the tap through them several times to get any burrs out.:beer:
- Joined
- Apr 26, 2010
- Messages
- 4,175
- Points
- 83
If there is a next time, I'll be sure to not short change myself and get a larger order, for $2 these seem pretty decent. Thanks a ton for hosting this!
