Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Why not Button cells?

Joined
Nov 14, 2010
Messages
44
Points
0
i always hear of people using lithium and 3.7 volt battery's which are expensive when you can be like me and go buy a pack of 100 1.5v button cells from dx for 3 bucks? i bet it fits better and a longer life but the button cells are so cheap i wouldnt ever pass it up even if i had to replace more often.

anyways i bought those batteries and a flashlight for my 405nm. im thinking of making two packs of 7.5v and putting them in parallel for longer life which still should fit easily in the host.
 
Last edited:





Joined
Aug 5, 2010
Messages
21
Points
0
It's because many button cell batteries can't supply the current needed to power anything stronger than a 5mw pointer. Also, a laser would them dry very fast, as button cells don't have a good watt-hour to size ratio.
 
Joined
Nov 14, 2010
Messages
44
Points
0
It's because many button cell batteries can't supply the current needed to power anything stronger than a 5mw pointer. Also, a laser would them dry very fast, as button cells don't have a good watt-hour to size ratio.

would two sets in parrelel be able to power a 200mw red or 125ma driver for a 405?
 
Joined
Jan 2, 2009
Messages
11,800
Points
0
Lasers need good batteries because of the current they draw. You want the best battery you can get. Which is usually a lithium ion cell. Those button batteries are made to power ultra low current draw devices. So its a wast of time, and money to play with those button batteries.
 

vk2fro

0
Joined
Nov 30, 2009
Messages
1,304
Points
63
Button cells have their uses, but they are only used in low current devices, and for their tiny size.

Examples:
Motherboard clock batteries
Hand held video games of yesteryear (think donkey kong)
Watches
Camera backup and remote controls
pocket universal remotes (used often to turn off TV's at public places)


all of these are low current applications. The most that is called for in these applications is around 15-20ma, in pulses, to drive the LED in a remote control.

The "play with your pet" dollar store lasers also draw a small (relatively to a 125mw pointer) amount, so you do get a reasonable time out of the batteries (usually measured in hours, or for a really poor driver, 10's of minutes).

Lithium ion batteries like the 18650 etc, can source several amps, and keep doing so right through their discharge curve. When they go flat, the laser will go really dim, really quickly, indicating time to change. This is the same reason laptops use these batteries. I get around 4 hours out of my dell on a full charge at minimum brightness in power saver mode. The screen at that level is still amazingly bright!
 
Last edited:
Joined
Nov 14, 2010
Messages
44
Points
0
Button cells have their uses, but they are only used in low current devices, and for their tiny size.

Examples:
Motherboard clock batteries
Hand held video games of yesteryear (think donkey kong)
Watches
Camera backup and remote controls
pocket universal remotes (used often to turn off TV's at public places)


all of these are low current applications. The most that is called for in these applications is around 15-20ma, in pulses, to drive the LED in a remote control.

The "play with your pet" dollar store lasers also draw a small (relatively to a 125mw pointer) amount, so you do get a reasonable time out of the batteries (usually measured in hours, or for a really poor driver, 10's of minutes).

Lithium ion batteries like the 18650 etc, can source several amps, and keep doing so right through their discharge curve. When they go flat, the laser will go really dim, really quickly, indicating time to change. This is the same reason laptops use these batteries. I get around 4 hours out of my dell on a full charge at minimum brightness in power saver mode. The screen at that level is still amazingly bright!




i think two packs of 7.5v in parrellel should be sufficient to power 125ma driver for a 405nm. if that goes well ill see how it works with a 650nm.

it was only 3 bucks so if if it sucks its not a big deal. considering i get 100 to play with and see if they work. but im almost positive it will work with the 405nm.
 
Joined
Jan 2, 2009
Messages
11,800
Points
0
i get 100 to play with...

...and throw in the trash. For an extra $3 you can get a proper battery and save the pollution. Plus your laser will work like it should. Its a no brainer, but I know some people have no brain, so act accordingly.
 

vk2fro

0
Joined
Nov 30, 2009
Messages
1,304
Points
63
hehe he could chuck them in a campfire - they make a good noise when they pop :p j/k

btw welcome back TJ
 
Joined
Jan 2, 2009
Messages
11,800
Points
0
hehe he could chuck them in a campfire - they make a good noise when they pop :p j/k

btw welcome back TJ

Tanx.

When I was younger I tried to charge one with a 12v car battery charger. It exploded in my face, and completely disintegrated.
 
Joined
Jul 17, 2010
Messages
2,160
Points
0
T. J. That's Brilliant!!! I tossed a 2x2 magnesium block into a lit fireplace when I was 17. BAD IDEA..melted the iron log holder, and cracked the fire brick. I thought the the chimney was gonna go up in flames as well...nearly Sh*t a brick.
 
Joined
Nov 14, 2010
Messages
44
Points
0
its to bad because some HAS done it before and HAS worked. kipkay did it with the lighter phr instructable. and he also used a driver.
 
Joined
Jan 2, 2009
Messages
11,800
Points
0
its to bad because some HAS done it before and HAS worked. kipkay did it with the lighter phr instructable. and he also used a driver.

Yeah..Kipkay is considered a moron here. He knows nothing about lasers, or laser safety.

What Kip doent show you is that it only lasts for around 30 seconds. What good is that? You have to rip it apart every 30 seconds to change the batteries. Pretty stupid laser project. Kip uses tactics in order for you to buy his over priced diodes, and other junk. You can check his rep yourself, he is a member here.

http://laserpointerforums.com/members/kipkay/
 




Top