1W 445nm laser (Yobresal build)

This is a short review of my Yobresal build laser as I promised him that I'll do a review about.

This is my latest laser which I am happy with it so far. With the first one I have many problems (it started with my fault trying to see which driver is in
I had so much problems while trying to have this laser but it worths it.

Not so many of Yobresal build laser users have given details about therefore I am not sure if they all are the same.
I think my first one has a different lens or a different set of focusing ring and lens because I was unscrew the ring almost it comes out to have a parallel beam (focused to infinity). This one has a different set so just 1-1,5 turn is enough to achieve that.

Reading is always more difficult than watching so I prefer to use photos rather than words
Here are the photos and at bottom a video that shows burning a hole in a white thick paper (All laser users know that it is the most difficult think to burn a whole with a laser (especially when it is not focused) as it reflects laser the most.
Lighting a match with 1W laser is a piece of cake I also tried that at 3m and it succeeds without focusing in 1-3seconds.

I want to add that copper heatsink is much better for cooling. First one with aluminium heatsink gets hot easier but upgraded version gives you more time before it get hot.

Laser in daylight (early evening)


Size comparison


Size comparison


Yobresal laser


GITD cap on


GITD cap off


focusing ring adjusted for parallel beam


top view


Top from the side (focusing ring is just above the top of the crown of the laser)


Battery compartment


clicky switch tail cap inside


clicky switch tail cap


driver circuit view through host


16340 batteries side by side(Spiderfire-Trustfire-Juice)


Juice


Trustfire


Spiderfire


2 juice batteries in


2 trustfire batteries in


2 spiderfire batteries in


GITD caps


GITD caps (the one on the left has a bulge inside that fits in focusing ring)


Laser in daytime from 8 meters)


Dot of laser at 8 meters


Dot of laser at 8 meters behind laser goggles


Dot size at 8 meters behind laser goggles (about 12mm long and 1mm wide)


This is a thick magazine page that is white in color


This is the burn made in 12seconds by this laser


This is the same burn from opposite side.


burning video:
YouTube - 1W laser burning a hole through white paper

Nice write up, and good pictures as well. I believe I was the first view on your video, Looks like you just posted it today. I have a very similar laser myself. However mine was purchased from Jayrob, it has the copper heat sink as well. I think the Cree C6 is just about the most common host used these days. Anyway, thanks for posting and enjoy your laser! :beer:

LORDJET said:

Nice write up, and good pictures as well. I believe I was the first view on your video, Looks like you just posted it today. I have a very similar laser myself. However mine was purchased from Jayrob, it has the copper heat sink as well. I think the Cree C6 is just about the most common host used these days. Anyway, thanks for posting and enjoy your laser! :beer:

Click to expand...

Yes I posted it new. Thanks for your comments.
About photos it is a bit difficult to take them if the lighting is not enough and also need to hold it with one hand and hold the camera with the other and also not to shake it to have clear photos while taking with no flash
About that Cree C6 host I am not sure who first discovered it but it is most likely the best for heatsinking and batteries.
And anyone can get from Survival Laser Home too.
Jayrob also has nice build and quality builds. Thanks for all these members for their work.

The thumbnails are unclickable btw (doesn't open a bigger version of the image when you click on them). Idk if you ment it to be like that but would be nice to be able to view the images full sized

X FLY said:

The thumbnails are unclickable btw (doesn't open a bigger version of the image when you click on them). Idk if you ment it to be like that but would be nice to be able to view the images full sized

Click to expand...

Thanks for letting me know about that mistake
As I didn't upload from my account I hardly find the correct links but I corrected them at last
Here they are!
Hope you like the large files

Yep now they work thanks :]

Did anyone noticed that when you shoot the laser to a wall (5m away) the dot of this 445nm LD is a small rectangle which has the long sides looking up and down and short sides looking sides
___________
I__________I

however if you check that rectangle at a closer distance (about 1m) it makes a quarter turn(90degrees) and long sides looking at sides.
__
I...I
I...I
I...I
I...I
I...I

weird?
:thinking:

murrat said:

Did anyone noticed that when you shoot the laser to a wall (5m away) the dot of this 445nm LD is a small rectangle which has the long sides looking up and down and short sides looking sides
___________
I__________I

however if you check that rectangle at a closer distance (about 1m) it makes a quarter turn(90degrees) and long sides looking at sides.
__
I...I
I...I
I...I
I...I
I...I

weird?
:thinking:

Click to expand...

I haven't noticed anything like this yet, probably because I always either burn from a close distance or shoot it way farther than 5m Probably just some kind of an illusion thats caused by the wavelenght of the light.

How many mA's are you running this on?

Very nice, and smart upgrading to copper. On all these smaller hosts aluminum should be phased out completely. GJ

X FLY said:

I haven't noticed anything like this yet, probably because I always either burn from a close distance or shoot it way farther than 5m Probably just some kind of an illusion thats caused by the wavelenght of the light.

Click to expand...

It's not an illusion -- I've seen the same thing in my 445nm diode lasers.
From a laser expert whos work I trust, comes this:

"Dear Craig Johnson,

I saw your stuff on the Arctic having major axis in one direction at 12 inches and 90 degrees from that at 7 feet.

Look for someplace in between where the beam is round.

The reason for this is usually astigmatism - where the beam has divergence from one axis corresponding to one "waist location", and divergence from the other corresponding to a different "waist location". Laser diodes often do this, while in general other lasers do not.

The "waist" is where the beam is narrowest. The beam converges approaching the "waist", and diverges after passing through the "waist".

Sometimes the waist does not exist in reality, but only as a mathematical projection of its existence rearward of where the beam starts. In that case, the beam diverges every inch of the way from where it actually starts.

A cylindrical lens can be used to move either the "parallel to E-field waist" or the "perpendicular to e-field" waist. If the two coincide into a single waist, then the beam has the same shape at all points far from the waist. (In the waist, the 90 degree difference happens again if the beam is oblong - lower divergence and wider waist width go hand-in-hand.) "