Aaron
0
- Joined
- Oct 26, 2010
- Messages
- 176
- Points
- 0
I am gonna buy this kit now :bumpit: It would work with an O-like 18650 w/ charger and a 445 diode, right?
LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
1.6W 445 Mohrenberg 18650 Host+Heatsink Kit Review + Tutorial
- Thread starter DTR
- Start date
DTR
0
- Joined
- Jun 24, 2010
- Messages
- 5,684
- Points
- 113
Are you asking if it will work with an O-Like module. as for the other questions it is a 18650 host and the unit I built is a 445.
- Joined
- Apr 4, 2010
- Messages
- 262
- Points
- 0
DTR, you take freaking awesome pictures! and you write great reviews. +rep
Edit: 200 posts! not much for many of you, but quite the accomplishment for me^^
Edit: 200 posts! not much for many of you, but quite the accomplishment for me^^
Aaron
0
- Joined
- Oct 26, 2010
- Messages
- 176
- Points
- 0
No, I meant this: 18650 Lithium rechargeable battery with charger [OL-18650] - $6.20 : Welcome to O-Like.com, Your source for laser products
I didn't know if it would fit because it's not protected, therefore is smaller than protected 18650's.
Aaron
0
- Joined
- Oct 26, 2010
- Messages
- 176
- Points
- 0
Here is my own version of this host
WARNING: HUGE PICTURES
http://dl.dropbox.com/u/9693610/photos/lasers/100_1190.jpg
http://dl.dropbox.com/u/9693610/photos/lasers/100_1192.jpg
http://dl.dropbox.com/u/9693610/photos/lasers/100_1189.jpg
Which DX driver is it?
DTR
0
- Joined
- Jun 24, 2010
- Messages
- 5,684
- Points
- 113
This host will fit protected and unprotected cells so it should work just fine. I am not aware of the quality of the battery though. It does say it is a 2200mAh.:beer:
Aaron
0
- Joined
- Oct 26, 2010
- Messages
- 176
- Points
- 0
Ok, I bought the kit. I just hope I dont get too impatient waiting for it to show up. I hear Moh ships fast though
DTR
0
- Joined
- Jun 24, 2010
- Messages
- 5,684
- Points
- 113
I normally get stuff the next day but I am a four hour driver from him.:beer:
- Joined
- Sep 13, 2010
- Messages
- 443
- Points
- 18
Re: 1W 445 Mohrenberg Host+Heatsink Sweeeet Review + Build Tutorial
Do you have to bridge the case pin with the negative pin on the diode for it to work?
Do you have to bridge the case pin with the negative pin on the diode for it to work?
jayrob
0
- Joined
- Sep 21, 2007
- Messages
- 9,862
- Points
- 113
Re: 1W 445 Mohrenberg Host+Heatsink Sweeeet Review + Build Tutorial
On a case negetive normal build, you can bridge the case pin on a blu-ray or 445 diode if you need to. But that is if it's for a FlexDrive. Not for a MicroBoost. The MicroBoost is different. Refer to the explanation and picture shown here:
http://laserpointerforums.com/f55/r...-taking-payments-now-48664-21.html#post781362
On a case negetive normal build, you can bridge the case pin on a blu-ray or 445 diode if you need to. But that is if it's for a FlexDrive. Not for a MicroBoost. The MicroBoost is different. Refer to the explanation and picture shown here:
http://laserpointerforums.com/f55/r...-taking-payments-now-48664-21.html#post781362
Last edited:
DTR
0
- Joined
- Jun 24, 2010
- Messages
- 5,684
- Points
- 113
Re: 1W 445 Mohrenberg Host+Heatsink Sweeeet Review + Build Tutorial
If this is the host you are planning on using the driver and diode I sold you on I will solder the negative driver input to the case pin.:beer:
This host does not have a good place to get the negative contact from the host so the case pin is used or you can bridge the negative pin and the case pin to provide a ground which would be difficult since I have already soldered the negative pin on the diode and covered it with shrink tubing.
If this is the host you are planning on using the driver and diode I sold you on I will solder the negative driver input to the case pin.:beer:
This host does not have a good place to get the negative contact from the host so the case pin is used or you can bridge the negative pin and the case pin to provide a ground which would be difficult since I have already soldered the negative pin on the diode and covered it with shrink tubing.
Last edited:
- Joined
- Sep 13, 2010
- Messages
- 443
- Points
- 18
Re: 1W 445 Mohrenberg Host+Heatsink Sweeeet Review + Build Tutorial
Yep this is the case I was planning on using. And :thanks: a lot.
Yep this is the case I was planning on using. And :thanks: a lot.
DTR
0
- Joined
- Jun 24, 2010
- Messages
- 5,684
- Points
- 113
Re: 1W 445 Mohrenberg Host+Heatsink Sweeeet Review + Build Tutorial
Alright then I will set it up with the negative driver input to the case pin tonight and send it out tomorrow.:beer:
Alright then I will set it up with the negative driver input to the case pin tonight and send it out tomorrow.:beer:
- Joined
- Sep 13, 2010
- Messages
- 443
- Points
- 18
Re: 1W 445 Mohrenberg Host+Heatsink Sweeeet Review + Build Tutorial
And I thought O-like had great customer service: you're awesome.
EDIT: Fixed spelling error
And I thought O-like had great customer service: you're awesome.
EDIT: Fixed spelling error
Last edited:
Aaron
0
- Joined
- Oct 26, 2010
- Messages
- 176
- Points
- 0
What host was your EZ Focus Adapter sized to fit? I just bought this kit
- Joined
- Sep 13, 2010
- Messages
- 443
- Points
- 18
@DTR: I noticed that you wrapped the driver in electrical tape. Should I do this with the flexdrive I am using in mine? I am using the same host and you set it to 1.5A
Last edited:
