Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

"Ribbed Silver" - 5-Mode 445nm Pico Build - 650mW

rhd

0
Joined
Dec 7, 2010
Messages
8,469
Points
0
This was my hardest build to date. Substantially harder than building a Pocket CR2 or Pocket Mini. In fact, I'd even venture to say that it was more difficult than building a whole 1085 inside the Coleman CR2.

I'm calling this the "Ribbed Silver". I don't know if this host has been done before, but it's a tough guy to work with. This guy is putting out 650mW peak (but through an acrylic lens - eek!)

attachment.php


Luckily, the inside "guts" are EXACTLY the same width as an Aixiz module (bonus!). However, there's just no way to use a bulky (*hehe*) driver like a Flexdrive or NJG-18 in this host. Basically the options I could think of were AK-007 (fairly untested as of yet) or stock LED driver (totally untested). I had the latter (obviously came with the host) and not the former. So, stock LED driver it was. The benefit? 5 modes! The downside? 2 of them are stupid. Also, it seems to be capable of less current than a similarly sized AK-007.

You need a decent ceramic cap when using a LED driver. The only way to make that fit in this host, is to solder an SMD ceramic cap across the diode leads. Truly no room for an axial cap in this build.

attachment.php


So, aixiz module gets pressed into the stock capsule, and the driver gets bookended onto that. It ends up looking like a bullet:

attachment.php

attachment.php


Before reassembly, here's what the pieces look like. Note that the 10440 (AAA sized) battery is roughly 60% of the entire host's size!

attachment.php


Here it is running, and compared to some other common hosts (my cameraphone is no good at capturing beam color):
attachment.php


And another generic beam shot:
attachment.php


I haven't LPMd it yet, but the max current when I tested the driver on a test load was around 580mA with batteries that had been charged a few weeks ago, but should otherwise have been fairly fresh. Better quality batteries and a totally fresh charge might improve this.

One final note, the driver has a neat thermal protection circuit in it, such that when it gets too hot (about 30 seconds on high mode!) it reverts into the lower "pulsed" mode. It's actually a decent approach to keeping the driver cool. Needless to say, duty cycles should be incredibly low.
 

Attachments

  • 1 - driver.jpg
    1 - driver.jpg
    121.3 KB · Views: 1,233
  • 2 - bullet A.jpg
    2 - bullet A.jpg
    139.4 KB · Views: 1,202
  • 3 - bullet B.jpg
    3 - bullet B.jpg
    135 KB · Views: 1,179
  • 4 - pieces.jpg
    4 - pieces.jpg
    126 KB · Views: 1,168
  • 5 - comparison.jpg
    5 - comparison.jpg
    157.8 KB · Views: 1,167
  • 6 - beam.jpg
    6 - beam.jpg
    124 KB · Views: 1,186
  • Final Build.jpg
    Final Build.jpg
    100.4 KB · Views: 1,318
Last edited:





Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

That's such a beautiful little bigger. I take it the host is the heatsink?
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

A gorgeous build, sounds like it was a bit painful as well.
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Nice. There really is something about these tiny builds that I really like!
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Very nice build man:), I've seen this host but thought it was awefully small to work with. Excellent job!
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Nice build, it would make an excellent pocket laser :)
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Nobody made the joke yet!!

Ribbed, for her pleasure. :p
(Sorry, I'm always the guy who voices the joke that we were all thinking...)

Nice build. How many milliWatts?
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Very nice build there RHD!
I love the micro/mini builds like this one. I think that my 10440 build is my favorite.
It will always blow peoples minds when you show it to them as well, they just don't expect to see so much light and power coming from such a small package!
:gj:
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Really beautyfull host! Would love to see a 405nm inside that host :o
Care to share where you got it? Also what kind of switch does it use? Doesnt look like.a regular tail clicky..
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Twist on...twist off. Deal extreme.
 
Last edited:
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

532, Xtrm2Rick, LaZeRz, Tonga, jcranmer, NetGod3Com, Wolfman:
Thanks for the positive feedback!

JaiNobeZ:
Hmmm.... I may have been thinking along those lines when I named her ;)
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

I did suspect that may have been the case.
Wait...

Named HER!?

O_________________________________________________________________O
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Oh, good point - this needs to be a male laser...

Damn, this one is so small and sexy looking, I really hate to think of it as a guy....
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

Oh, good point - this needs to be a male laser...

Damn, this one is so small and sexy looking, I really hate to think of it as a guy....

You know there's a problem when you're calling lasers sexy... ;)
 
Re: "Ribbed Silver" - 5-Mode 445nm Pico Build

650mW output (with acrylic lens) - just LPMd it.
 
Last edited:


Back
Top