Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Heat shrinking tubing

LordKaramazov

LordKaramazov

0
Joined
Nov 18, 2009
Messages
269
Points
0
Hey,
I know some people use heat shrinking tube, so i thought to start this thread so beginners in the DIY like me and many others can safely use this great method of isolating the wires so they dont short-circuit and to keep our solders safe!

So im asking the great minds and hands of the DIY:
Whats the best way of shrinking the tubbing without damaging any component?? Especially the expensive LD!

:thanks: and have a nice day! :yh:
 





daguin

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
LordKaramazov said:
Hey,
I know some people use heat shrinking tube, so i thought to start this thread so beginners in the DIY like me and many others can safely use this great method of isolating the wires so they dont short-circuit and to keep our solders safe!

So im asking the great minds and hands of the DIY:
Whats the best way of shrinking the tubbing without damaging any component?? Especially the expensive LD!

:thanks: and have a nice day! :yh:
Click to expand...

Shrink tubing requires <200 degrees. It should pose no problem to the diode.

Peace,
dave
 
HIMNL9

HIMNL9

0
Joined
May 26, 2009
Messages
5,318
Points
0
Hot air blower is the more common way, i suppose, or at least is the more common one that i use :p

Also big hot blowers (those used for scrap paint, high temperature), at middle position, are ok, cause it require just a second or two for shrink, so components don't get damaged.

In some emergency cases or field works, i use also lighter, but this require a bit of experience, for not damage things and do it in the right way.


Edit: if the time is not a problem and you're a patient person with steady hand, also just keeping the soldering iron near the tube (1 mm of distance from the tube), preferably under it (hot go up ;)), and moving it slowly, rolling the wire until all is retracted, is a working system.
 
Last edited:
phoenix77

phoenix77

0
Joined
Apr 1, 2008
Messages
3,924
Points
0
I just use the tip of my soldering iron to shrink the tubing........rob
 
lasersbee

lasersbee

0
Joined
Sep 20, 2008
Messages
17,622
Points
113
A Heat Blower for scraping paint may be too hot up close...
You can adjust the temperature of that Hot Air Blower by adjusting
the distance between the Blower and the heat shrink..

We use an adjustable Industrial Hot Air Blower by Master Appliance
Corp.:cool:

Jerry
 
LordKaramazov

LordKaramazov

0
Joined
Nov 18, 2009
Messages
269
Points
0
because i bought the heat shrinking tube, but im not thinking in buying a hot air blower...ill try the hair drier first...if it doesnt work ill try the soldering iron method...and in last resource...hmmm...no i wont use fire
 
lasersbee

lasersbee

0
Joined
Sep 20, 2008
Messages
17,622
Points
113
You will need a High Wattage Hair Blower and you will need to concentrate
the air flow to a small point with some type of metallic funnel.

Jerry
 
Bionic-Badger

Bionic-Badger

0
Joined
Oct 26, 2007
Messages
5,438
Points
83
I can only imagine how many little electrical parts will fly off your desk with a hair dryer. I'd stick with the soldering iron, since it's usually handy anyway.

Just put it near the heatshrink (don't touch it!) and the radiant heat will quickly start the heat shrinking.
 
lasersbee

lasersbee

0
Joined
Sep 20, 2008
Messages
17,622
Points
113
:crackup::crackup: yeah I can just see that...

We have a stand on our Heat Gun... and place it on the bench
facing towards the center of the shop... then manipulate the part
that needs heat shrinking into the hot air stream...:cool:


Jerry
 
lazer

lazer

0
Joined
Dec 21, 2008
Messages
361
Points
0
phoenix77 said:
I just use the tip of my soldering iron to shrink the tubing........rob
Click to expand...

Same here. I like the soldering iron method because you can keep the heat away from the components instead of hitting the whole thing with a heat gun.
 
Tech_Junkie

Tech_Junkie

0
Joined
Jan 2, 2009
Messages
11,800
Points
0
I use a lighter 99% of the time. Dont touch it with the flame, just hover the tube over the flame. It works fine if you go slow.
 
phoenix77

phoenix77

0
Joined
Apr 1, 2008
Messages
3,924
Points
0
I think the soldering iron method is the easist & safest way to go................. rob
 
LordKaramazov

LordKaramazov

0
Joined
Nov 18, 2009
Messages
269
Points
0
ill try the iron then first^^

i was thinking in something more 'aggressive' like TJ style of shrinking...

but ill just use the iron first

thanks all
 
You must log in or register to reply here.




Top