Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Got The Bench Basics. What Do I Need Now?

Joined
Feb 10, 2013
Messages
2,125
Points
63
So, I've got my bench PSU, good DMM, soldering station, Ophir 5W sensor, and I've got good test leads.

What are some of the things that don't get discussed much around here (soldering heatsinks, etc) that really should be in all of our tool boxes or on our benches to handle: a) direct drive diodes for measuring, b) adjusting drivers, c) testing builds before assembly, d) fault diagnosis?

Blord once showed me a pic of a little plastic doodad that slipped onto diode pins to protect them. I still don't know what to call it or where to get it.

These are the kinds of things I'm asking about. Hopefully we can all learn something from this thread.
 





ARG

0
Joined
Feb 27, 2011
Messages
6,772
Points
113
An oscilloscope is handy for measuring driver ripple. You can get cheap used ones on Ebay or Craigslist. A digital scope can also measure start up spikes, but they are not as cheap.

I even got an old scope for free on craigslist. :)
 
Joined
Feb 10, 2013
Messages
2,125
Points
63
Thanks, ARG. I was thinking more about the little things that noobs might not know about...eg: upgraded test leads, using test clips, etc.

That being said, I'd love an oscilloscope, but I should learn how to use one first. Still early in a CE course. lol
 

norbyx

0
Joined
Apr 18, 2013
Messages
1,202
Points
48
Why would you need to measure the driver ripple? can it be changed or adjusted?
 

norbyx

0
Joined
Apr 18, 2013
Messages
1,202
Points
48
Big Ripple Kill Little Diode.

If you're a driver builder...

Agreed but if you aren't able to mod a driver because you don't have the knowledge than it would be just to avoid connecting the driver to the diode and busting the diode.... I mean the scope would be just to check the driver and in the eventuality send it back to the seller....
 

ARG

0
Joined
Feb 27, 2011
Messages
6,772
Points
113
@norbyx
It's not just for building drivers, or modding the drivers. I like to test my drivers before hooking them up to a 130$ PL-520 diode :p
I've killed ~300$ in diodes, half because of a poor driver. Having the tools to test the driver is very useful.

@Topic
A reflow gun can be useful to remove resistors from drivers to change the output value of the driver.
 

norbyx

0
Joined
Apr 18, 2013
Messages
1,202
Points
48
Well than, sticking with the topic, a dummy load would be usefull...
 
Joined
Dec 17, 2012
Messages
2,081
Points
63
Ive used the clip copper heat sinks quite a bit. If not being used as a sink it makes a great little clip for holding wires while soldering. Also works well if you have heatshrink tube on a very short wire from allowing the heat to travel the wire and shri k the heatshrink prior to it being in the proper location. If that makes any sense.
 

DinNY

0
Joined
Apr 5, 2013
Messages
23
Points
0
Judging by your join date and post count .. I'm guessing some sunlight might be in order :p
Look out daguin .. you've got competition !! :D

Seriously though .. I have little anti-static foam cubes that work great for protecting leads .. couple that with the little silicone "condoms" that come on all things e-cig. and you've got a great little container for storing diodes..

Little harvesting tools also .. plastic prys .. torx bits, small cutters, pliers, solder sucker/reflow gun & wick, etc ..

Proper ESD gear .. and "Helping hands"
 
Last edited:
Joined
Oct 26, 2007
Messages
5,438
Points
83
- A good vise for holding your boards. Sometimes those helping hands just don't cut it. Get a nice project vise for holding the boards or other parts (base 1, base 2; holder; junior version).

- A solder sucker. I suck with solder braid, and sometimes I need to get that excess solder out of a hole on the board. This tool is just great for that. Spring-load the action on the sucker, melt the solder, push the button and the solder is sucked out of the location. Fast and efficient.

- Some good liquid flux. I've already got two small bottles of Kester 1544 that'll last me forever. You might want some of the flux FlamingPyro offers so you don't have to buy a gallon + hazardous material shipping (actually a decent price, but you'd never go through it.

- An automated wire stripper. Yeah it seems lazy, but I love this thing. Just put the wire in to the length you need, squeeze, and the wire is stripped. I find it faster than pliers, and I don't damage wires with it.

- An assload of heat shrink wrap to cover your wires (get it at DX) and a hot air gun for melting heat-shrink wrap like this.

For more advanced stuff, a toaster oven and controller for low-level reflow on designed PCBs. Having a vacuum pen is also nice (note that it helps to have a separate suction controller off of the pen so that you don't shift the part when you release, as mentioned in this excellent video).
 
Joined
Dec 23, 2008
Messages
3,948
Points
63
Agreed but if you aren't able to mod a driver because you don't have the knowledge than it would be just to avoid connecting the driver to the diode and busting the diode.... I mean the scope would be just to check the driver and in the eventuality send it back to the seller....

^ Let's stick to the thread topic and save the instrument use for another one.

I would say that is on topic. It's good to have all the facts to make an informed decision. What if nobody else replied and a noob saw this and said "hmmm, I have to get a scope" that be a huge waste of money. Normally we say let's not derail a thread after many derailed posts. It's good to let a little dialog fly. :wave:

Michael


Michael.
 

DinNY

0
Joined
Apr 5, 2013
Messages
23
Points
0
Wow, nice post BB +1..
All things I take for granted.
I think the wire stripper @ work cost ~$250K.
Flux by the drum, and shrink tubing by the mile.

as a side note .. anyone know the spec for the silicone wire we have all come to love?

Back on topic .. A bench top lathe would be nice .. I think it will be my next "investment" for the home .. Harbor Freight had them on sale recently .. but I missed it ..
 
Joined
Feb 10, 2013
Messages
2,125
Points
63
Well, thanks everybody. I guess I am more covered than I expected...minus the oscilloscope. Which I only moved away from in the thread, as I would consider that an advanced bench instrument, rather than a basic tool that guys like me, getting into lasers, might not already be familiar with.

I have miles of solder, drums of flux, solder suckers, solder wicking, heat gun, heatshrink everywhere, full-on BPM anti-static setup, tiny dykes, strippers galore, micro tweezers, helping hands, solder cleaner, acetone, isopropyl, KTP, neodymium magnets of many sizes, intelli-chargers, and so on....
 

DinNY

0
Joined
Apr 5, 2013
Messages
23
Points
0
lol, just seen "New to veteran status" :D
guess I'll eat my words now .. congrats !!
 




Top