Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Diode dead weird flexdrive thing.

wolfhunter9154

wolfhunter9154

0
Joined
Oct 21, 2009
Messages
204
Points
18
I was working on my phr build today and i was using a kryton groove (kind of overkill). The tail switch didn't work but I didn't know that yet. I took everything out and tested it. I tested the circuit i set up and it powered the diode. Then I tested the tail switch and discovered the problem. Anyway, I was playing around 5 minutes later and this time the diode wouldn't light up. I checked voltages and currents and the flexdrive is giving out 1 amp even thought it is on the 66-100 setting. Any ideas?
 





Bionic-Badger

Bionic-Badger

0
Joined
Oct 26, 2007
Messages
5,438
Points
83
Is it disconnected (bad solder joint, etc.)? The current will continue to ramp if there is no load.
 
MarioMaster

MarioMaster

0
Joined
Jul 27, 2007
Messages
3,642
Points
63
Which means something else strange is going on - the flexdrive would do nothing if it was toasted.
 
wolfhunter9154

wolfhunter9154

0
Joined
Oct 21, 2009
Messages
204
Points
18
IMG_0338.jpg

IMG_0337.jpg

IMG_0339.jpg

IMG_0340.jpg


these are pics of the driver and solder joints
 
Kevlar

Kevlar

0
Joined
Apr 26, 2010
Messages
1,353
Points
48
I was hoping by looking at the pictures that there might have been some solder jumpers wrong or something but it looks like default setting like you said.

When you check the voltages and currents did you use a test load? If so, did you try adjusting the pot?

Obviously if 1A went to the PHR, it is most likely dead but just trying to figure what is going on with the flexdrive. :thinking:
 
daguin

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
The solder joint to the positive pin looks cold.

How are you measuring the current?

Peace,
dave

**EDIT** -- Where/why are you using all that wire in a Kryton?
 
Last edited:
daguin

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
wolfhunter9154 said:
What do you mean cold? Also it looks like a lot more wire in the pics.
Click to expand...

A "cold" solder is one in which there was not sufficient heat to cause the solder to "flow" smoothly. This can result in momentary (or permanent) breaks in the joint.

I asked about the wire, because I don't know of anyone that uses wire as more than a "jumper" in a Kryton build. Here is a shot of an older one I did. Notice how old the flexdrive is ;) Some old timers might even recognize the Kryton Smooth head :)


krytondriver.jpg

I don't even use that much wire anymore. The diode pins are soldered directly to the driver now. There is NO wire in the build

You still have not said how your measured the current

Peace,
dave
 
wolfhunter9154

wolfhunter9154

0
Joined
Oct 21, 2009
Messages
204
Points
18
Ill be on after the weekend because I'm going to my cabin. I measured it with a digital multi meter. and I built it after I saw that you were supposed to attach the flex drive right on to the head.
 
Last edited:
daguin

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
wolfhunter9154 said:
Ill be on after the weekend because I'm going to my cabin. I measured it with a digital multi meter. and I built it after I saw that you were supposed to attach the flex drive right on to the head.
Click to expand...

With the multi-meter attached where? How was it powered? What was attached to the driver at the time you measured it?

Peace,
dave
 
You must log in or register to reply here.




Top