Since the blue ray diode puts out no infrared, does a glass lens still limit/no change/increase power output? Also, im considering a lpc815 build, using a rkcstr driver. Will this work down to 3.0v input? What would be an appropriate input voltage for this setup and a good tradeoff power level setting.
LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
blue laser question
- Thread starter terdy
- Start date
daguin
0
- Joined
- Mar 29, 2008
- Messages
- 15,989
- Points
- 113
No lens can "increase" the output of the diode. ANY lens will cause some loss of output.
The LPC diode needs 3V. The Rkcstr needs 2.2V. You need a minimum of 5.2V for it to regulate the laser. I like to work with a 6V minimum with the combination you have outlined here.
I'm not sure what you mean by "good tradeoff power level setting."
Peace,
dave
A tradeoff of life yet high power, that particular diode is advertised as 300mw, so say i could drive it at 250mw for a very long time. A flexdrive could be used for lesser voltage hosts, correct? I guess what im asking as far as the lens question is, i seem to see the opinions on the glass/acrylic lens issue go both ways. Whitch lens cuts the power least?
Thanks, and bear with me here!!
Thanks, and bear with me here!!
DJNY
0
- Joined
- Nov 2, 2009
- Messages
- 5,991
- Points
- 83
daguin
0
- Joined
- Mar 29, 2008
- Messages
- 15,989
- Points
- 113
Although there are NO guarantees about diodes, you should be able to run that diode at 380mA-420mA with a good life expectancy (as long as you do not let it overheat)
In order of allowed output (lowest to highest)
AixiZ acrylic
AixiZ glass (for red)
Merideth
650-G-1
You can search up these for additional info
Peace,
dave
Also, can a driver be set using a test load with an input voltage to the driver that is different from the final host output voltage. Say, setting the output voltage of either a rkcstr or lava boost drive, with 9v input to the driver, but using say a 7.2v host?
- Joined
- Dec 23, 2008
- Messages
- 3,948
- Points
- 63
almost all available multimeters have a 200mv setting and a 2v setting. if you want 200mv or less use 200mv. if more, then choose the 2v. setting. it is accurate to 3 decimal places usually. and yes you do not need the same input voltage for testing as you do in the final host.
please try searching. if you work for the info you will learn much more.
michael
please try searching. if you work for the info you will learn much more.
michael
i guess my fluke just auto ranges in mv mode, im getting the correct readings for a blue ray that ive just finished, i just couldnt figure out how setting the driver around 350 plus mv was equaling 220mw output, is it the loss through the lens? If i were to set the driver on a test load at those levels, wouldnt it fry the diode?
daguin
0
- Joined
- Mar 29, 2008
- Messages
- 15,989
- Points
- 113
I thought you had a couple of questions so I tried to help. It has become apparent that you are just looking for someone to tell you what to do. So I am telling you what to do . . . .
You need to read more. You are not ready to build a laser yet.
Peace,
dave
You need to read more. You are not ready to build a laser yet.
Peace,
dave
- Joined
- Dec 23, 2008
- Messages
- 3,948
- Points
- 63
ohms law is to help you turn mv into ma.... neither of those correlate into mw
michael
michael
