Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Please help me troubleshoot my first build...

Joined
Sep 28, 2009
Messages
32
Points
0
My first laser building attempt does not appear to be working all too well. I'll provide the details, so far, and can someone help me with some troubleshooting? The problem I'm experiencing is that I'm not getting much output.


Here's my setup...

- rkcstr driver configured for full range and adjusted until I got light from the diode, plus a little more (I figured it best not to push it until I built a test load to set it appropriately)

- LPC-815 diode removed myself (maybe I damaged trying to remove it...I don't know what to look for)

- Modwerx heatsink module with AR glass lens

- 4AA battery pack from Radio Shack with a 9-volt type snap connector.


My thoughts...

- I can focus to a pin point by adjusting the glass lens, but maybe I have it in backwards? What is front/back on these things? I noticed one side was sort of inserted into the other. That's the side I have facing the diode.

- Perhaps my battery pack is only spitting out 3V and not 6V...rigged parallel instead of series. I will check this with a volt meter when I get home tonight.

- I took care soldering the driver together so as not to have any shorts. I would assume if I did, I would have no ouput at all?

- Maybe I damaged the diode removing it from the LPC-815? What does a damaged diode look like? I did end up using my Dremel to cut into the aluminum, then used a screw driver to pry it apart. I was careful not to cut too far, but would the vibration be an issue? There doesn't seem to be anything vibration sensitive from looking at the diode.

- On a different noe, the last thing I noticed, is that the diode does not fit tight into the heatsink/module. Should it? There is a thumb ring that screws into the back that seems to hold the diode in. The only problem is that you can't solder the driver to the diode then as the rings spaces it out too far. Drew, perhaps you can provide some insight into this?

Thanks all,
Eric
 





Joined
Aug 1, 2008
Messages
335
Points
0
you might not have enough voltage.. ud need 5.25-12V for driving red diodes
 
Joined
Nov 7, 2008
Messages
5,725
Points
0
If you have two 3V batteries in parallel, you have 3V going in. To double the voltage, the batteries must be in series.
 
Joined
Sep 20, 2008
Messages
17,622
Points
113
Are you using fresh standard AA batteries (4 X 1.5V = 6volts)....
or NiHM AA batteries (4 X 1.2V = 4.8Volts)

1) check the actual voltage of your Battery supply under load...
2) if battery voltage is above 2.5Volts then use a Test Load...
to adjust and test your Driver's current...
3 when your driver's current is adjusted to where you want it...
turn it off and remove the Test Load..
4) short out the Driver's output capacitor....
5) connect your diode to your adjusted/tested driver...

If the LD has a strong beam... you're set to go
If the LD is very weak or does not lase at all... it's time to
get another LD....:cryyy:


Jerry
(3900-6465-81)
 
Joined
Aug 30, 2008
Messages
6,891
Points
83
i'm confused. you said you adjusted the driver untill it was outputting light....

so what exactly is the problem?

if your getting some light out of it, make sure it's at least 6 volts.
once you do that if it's still a dim light then you've killed your diode.
 
Joined
Sep 28, 2009
Messages
32
Points
0
Well, after some testing last night, I'm fairly certain I killed the diode. It looks fine upon visual inspection, but with 9 volts going in and the driver turned up, it's still only an LED at best...doh! It must have happened when I was trying to get it out of the heatsink. I'm only going to buy single diodes from now on...
 




Top