Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

My first red laser build

Joined
Mar 17, 2010
Messages
217
Points
0
This is the first red laser I built.
It has a 7mW 635nm red diode, a DDL driver (which was too long to fit in the host so it had to be cut in half and one half was placed under the other) and the current is around 50mA.
This wavelength is much brighter than 650nm and it's possible to see the beam in complete darkness. I can also see a little difference in color from 650nm, but others have said they see no difference.
I actually completed this laser almost a month ago, but I taught I'll wait until I get a better battery to post it however it seems it's not going to happen that soon so I just posted it now.
The batteries it uses now are three L1154 button cells.
Special thanks to Eudaimonium for providing me with this diode (and ReNNo who gave Eudaimonium the diode) and Billg519 who gave Eudaimonium the switch he gave me for this laser.
Here are some pictures:
IMGP1237.jpg


IMGP1238.jpg


IMGP1241.jpg


IMGP1242.jpg


IMGP1243.jpg
 





Joined
Apr 26, 2010
Messages
4,175
Points
83
WOOT WOOT! I just got one of these diodes, did you clip the pins down a little bit? These pins on mine are super long! I didn't know it had a visible beam in darkness though :drool: I definately have to go set this up, I'll just put my Rckstr on it's lowest setting. How long will it survive on 50mA?
 

ReNNo

0
Joined
Mar 27, 2009
Messages
589
Points
0
I'm glad that you found practical use of this diode.
This is very unusual host, and I like it...

Recommended current for this diode is 40mA, we can only hope that it will last on 50mA.

What I like about this diode is heat dissipation.
I powered this diode for 2-3 minutes and diode stayed cold. Hard to believe :)

Beam is visible in dark.
 
Joined
Feb 5, 2008
Messages
6,252
Points
83
I'm glad that you found practical use of this diode.
This is very unusual host, and I like it...

Recommended current for this diode is 40mA, we can only hope that it will last on 50mA.

What I like about this diode is heat dissipation.
I powered this diode for 2-3 minutes and diode stayed cold. Hard to believe :)

Beam is visible in dark.
The "host" is actually a plastic laser attachment fit for plastic toy gun.

We'll try to fix up a pressure pad on handle of the gun - that'll be badass.

It's a very nice diode though, I think I can also see a bit shade difference, but only when holding 650 nm and 635 nm side by side.
 
Joined
Mar 17, 2010
Messages
217
Points
0
WOOT WOOT! I just got one of these diodes, did you clip the pins down a little bit? These pins on mine are super long! I didn't know it had a visible beam in darkness though :drool: I definately have to go set this up, I'll just put my Rckstr on it's lowest setting. How long will it survive on 50mA?

Yes, I did clip the diode pins, they were really long.
I would have set a lower current if I could, but since the driver had to be cut like this it would be impossible to fit a regular resistor on it, so an SMD resistor had to be used and the closest Eudaimonium and I had to get that kind of current was 22ohm.
The beam can be seen, but it's really hard.
 
Joined
Feb 5, 2008
Messages
6,252
Points
83
Yes, I did clip the diode pins, they were really long.
I would have set a lower current if I could, but since the driver had to be cut like this it would be impossible to fit a regular resistor on it, so an SMD resistor had to be used and the closest Eudaimonium and I had to get that kind of current was 22ohm.
The beam can be seen, but it's really hard.
That's because you have 100mW green and 200mW bluray and 240 mW red next to it, maybe?

Compare it to red el-crapo keychains, not some amper-eaters.
 
Joined
Feb 21, 2008
Messages
1,056
Points
0
Congrats on completing your first red, and a 635nm, too. Even at 7mW (maybe you're getting a ferw more with the 50mA) the 635nm will be visible in darkened conditions. Have you tried for any beamshots with a little smoke or fog? Nice, creative build using materials at hand.
 
Joined
Mar 17, 2010
Messages
217
Points
0
Congrats on completing your first red, and a 635nm, too. Even at 7mW (maybe you're getting a ferw more with the 50mA) the 635nm will be visible in darkened conditions. Have you tried for any beamshots with a little smoke or fog? Nice, creative build using materials at hand.

Thanks! I haven't tried any beamshots because I don't have a smoke machine. The only thing I could use for smoke are matches. Also I just measured the current and it's only 22mA now, but what could I expect from three button cells. That's why I need a better battery like a 10180 li-ion.
 
Joined
Apr 26, 2010
Messages
4,175
Points
83
You could get a good bit of smoke from burning paper towles. Set it on fire for about 1-2sec, put it out but let it smolder (orange glowing edge) it will smoke then but won't burn away quickly. Keep doing that a few times and that gets more smoke than matches. You get about 2-3 times as much smoke with every smolder as you do with putting out a match.
 
Joined
Mar 17, 2010
Messages
217
Points
0
You could get a good bit of smoke from burning paper towles. Set it on fire for about 1-2sec, put it out but let it smolder (orange glowing edge) it will smoke then but won't burn away quickly. Keep doing that a few times and that gets more smoke than matches. You get about 2-3 times as much smoke with every smolder as you do with putting out a match.

Good idea. I'll try that.
 

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
Excellent, creative use of the materials on hand. :gj:

Peace,
dave
 




Top