Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Micro Boost and LOC 815 diode

DTR

DTR

0
Joined
Jun 24, 2010
Messages
5,684
Points
113
Mohrenberg said:
Hey, I thought everyone was saying this couldn't be done?

I have not gotten to use a micro boost yet.
Click to expand...

It can certainly be done. But you need to insulate the heatsink from the host which can be pain with most hosts.
 





DTR

DTR

0
Joined
Jun 24, 2010
Messages
5,684
Points
113
Mohrenberg said:
eeewwwww. That would be a pain
Click to expand...

That is why the good Dr. said "It is a very nonstandard setup but should work"

I guess they will be wrapping their heatsinks in electrical tape or run a new negative line that is not in contact with the host. Sounds like a pain in the ass to me.;)
 
gillza

gillza

0
Joined
Jul 26, 2010
Messages
583
Points
28
DTR said:
That is why the good Dr. said "It is a very nonstandard setup but should work"

I guess they will be wrapping their heatsinks in electrical tape or run a new negative line that is not in contact with the host. Sounds like a pain in the ass to me.;)
Click to expand...


Or use thermal epoxy to fix the module in the heatsink with some extra space. The bottom line is it can be done and someone may find the information useful.
 
DTR

DTR

0
Joined
Jun 24, 2010
Messages
5,684
Points
113
gillza said:
Or use thermal epoxy to fix the module in the heatsink with some extra space. The bottom line is it can be done and someone may find the information useful.
Click to expand...

Certainly wasn't saying it was not good info but that it would be hard to implement with most of the hosts that we are using.:beer:
 
gillza

gillza

0
Joined
Jul 26, 2010
Messages
583
Points
28
DTR said:
Certainly wasn't saying it was not good info but that it would be hard to implement with most of the hosts that we are using.:beer:
Click to expand...

Yep :) it would be a pain :) that is why I think I'll use that tortured microboost drive for my planned 12x Blu-ray build and wait for October to get few flexdrives for future Reds hehe
 
Morgan

Morgan

0
Joined
Feb 5, 2009
Messages
2,174
Points
0
^ You could also isolate the battery contacts from the host. This is sometimes easier if you can fit a wire beside the battery in the barrel and also keeps your heatsinking continuity. Just another option.

M
:)
 
RA_pierce

RA_pierce

0
Joined
Sep 16, 2007
Messages
3,658
Points
113
You can drill out the ID of the heat-sink 1mm or so larger so that the Aixiz module is "floating" inside (not a tight fit) then fill the gap with Arctic Silver/ Arctic Alumina or some other highly heat conductive, electrically insulating epoxy.
Shouldn't be too much of a PITA.

The Arctic epoxies are for permanent fixtures, though, and they may conduct electricity a tiny bit.
As far as thermal epoxies go, it is supposedly the best.
 
gillza

gillza

0
Joined
Jul 26, 2010
Messages
583
Points
28
RA_pierce said:
You can drill out the ID of the heat-sink 1mm or so larger so that the Aixiz module is "floating" inside (not a tight fit) then fill the gap with Arctic Silver/ Arctic Alumina or some other highly heat conductive, electrically insulating epoxy.
Shouldn't be too much of a PITA.

The Arctic epoxies are for permanent fixtures, though, and they may conduct electricity a tiny bit.
As far as thermal epoxies go, it is supposedly the best.
Click to expand...

Arctic silver definitely does. Arctic Alumina oxide/Ceramic should not conduct.
 
Juniortore1

Juniortore1

0
Joined
Aug 29, 2010
Messages
123
Points
0
Ths is just my opinion, and I do not need to be spammed by a 100 comment saying I am wrong.
I and my friend have powered red diodes with micro boost may times, and have worked great. A driver is a driver, they all regulate current, you could push in 400 volts DC in if you wanted, but as long as the current is limited to whatever mA is recogmended. Well, IDK about 400, that might mess with the insulation. But, that wasnt my point.
I would still rather flexidrive, but micro boost works.

ANd one quick question, does the flex drive boost current as the voltage gets low like the micro boost, rather letting the diodes power drop as the input drops.

Sorry about any spelling mistakes
 
gillza

gillza

0
Joined
Jul 26, 2010
Messages
583
Points
28
400V is a lot of energy it will fry your driver in a nanosecond.

Flexdrive is buck/boost it outputs the V below or above the battery's voltage to the Forward voltage of the LD.
 
paulzimm

paulzimm

0
Joined
Jul 22, 2008
Messages
288
Points
28
Question: What about Dr. Lava's FlexModP3 driver used for powering and modulating (TTL/analog) a laser diode. Is that a buck/boost driver as well? Could I use a 12V source to power a single 445 diode? I tested using a dummy load (1 Ohm resistor / 6 test diodes) and the voltage measured at the LD output is right around 5 volts. From the documentation, the FlexModP3 supports up to 24 volts and I don't know of any laser diodes that require that amount of voltage. My dummy load looks good with 12 volts but I don't want to risk frying my diode until I know for sure...

LINK - http://hacylon.case.edu/ebay/laser_diode/FlexModP3.php

EDIT - Nevermind! I got my (positive) answer here: How hot they run is entirely dependent on how much higher your power supply voltage is from the diode voltage, and the diode current.. if you're powering a single 4V, 800mA diode with a 12V supply, your heatsink has to dissipate 6.4 Watts. However if you used a 5V supply, it only has to dissipate 0.8 Watts.
 
Last edited:
Juniortore1

Juniortore1

0
Joined
Aug 29, 2010
Messages
123
Points
0
Okay, then I will get the flexi for my red laser, I just know that micro boost does work for red. But, since flexi is available, I will use that since it is recommended. And That is good, thats why I wanted either flexi or boost because with nearly all drivers, when the voltage drops, the current to the diode drops below what you have it set to. But, the flexi and micro boost rise the current to what you need as voltage drops

Thanks
 
gillza

gillza

0
Joined
Jul 26, 2010
Messages
583
Points
28
Juniortore1 said:
Okay, then I will get the flexi for my red laser, I just know that micro boost does work for red. But, since flexi is available, I will use that since it is recommended. And That is good, thats why I wanted either flexi or boost because with nearly all drivers, when the voltage drops, the current to the diode drops below what you have it set to. But, the flexi and micro boost rise the current to what you need as voltage drops

Thanks
Click to expand...

Flexdrives are still showing as out of stock on Dr.Lava's site... Hmm did I miss something, are they being redistributed through a middle man?
 
You must log in or register to reply here.




Top