Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

My DIY Spirograph

mikeeey

mikeeey

0
Joined
Jun 7, 2007
Messages
1,771
Points
0
thankyou!! this guide/picture really helped!
based off this picture, how can we change the direction of the motors? :)
 





T

thejunkmonger

0
Joined
Feb 4, 2008
Messages
510
Points
0
mikeeey said:
thankyou!! this guide/picture really helped!
based off this picture, how can we change the direction of the motors? :)
Click to expand...


swap the connection on the battery or add a Double POle Double throw switch
 
rog8811

rog8811

0
Joined
Jul 24, 2007
Messages
2,749
Points
0
I found a copy of one I posted some time back, this one uses 2 switches
One single pole switches it on and off
The other 2 pole changeover reverses one motor
Only one pot, wound right down gives the tunnel effect.

Regards rog8811
 

Attachments

  • Circuit02.jpg
    Circuit02.jpg
    82.3 KB · Views: 488
N

nikokapo

1
Joined
Dec 26, 2007
Messages
6,129
Points
0
rog, mikeeey asked me about this because he has little to no knowledge of electronics so i made a diagram with pictures to make it understandable :)

(hey thx for the help anyway ;))
 
rog8811

rog8811

0
Joined
Jul 24, 2007
Messages
2,749
Points
0
I posted it because yours didn't show the reversing switch (which I think was discussed :-/) and FML's link shows the reversing switch and not the whole circuit.

Mine also shows that you need a separate on/off switch because a double pole, centre off switch, will reverse both motors....

Regards rog8811
 
mikeeey

mikeeey

0
Joined
Jun 7, 2007
Messages
1,771
Points
0
rog8811 thanks for the diagram, but i must admit I'm a noob in electronics, and nikoapo's drawing is very easy for me to understand lol.

nikokapo said:
rog, mikeeey asked me about this because he has little to no knowledge of electronics so i made a diagram with pictures to make it understandable :)

(hey thx for the help anyway ;))
Click to expand...
nikokapo when you get a chance do you think you could add the seperate reversing switch's in your drawing? :) your's is the easiest for me to understand :p
 
mikeeey

mikeeey

0
Joined
Jun 7, 2007
Messages
1,771
Points
0
rog8811 said:
I posted it because yours didn't show the reversing switch (which I think was discussed :-/) and FML's link shows the reversing switch and not the whole circuit.

Mine also shows that you need a separate on/off switch because a double pole, centre off switch,  will reverse both motors....

Regards rog8811
Click to expand...
does radio shack have pole changeovers? thats what they're called right?
 
N

nikokapo

1
Joined
Dec 26, 2007
Messages
6,129
Points
0
rog8811 said:
I posted it because yours didn't show the reversing switch (which I think was discussed :-/) and FML's link shows the reversing switch and not the whole circuit.

Mine also shows that you need a separate on/off switch because a double pole, centre off switch,  will reverse both motors....

Regards rog8811
Click to expand...

alright! thanks :)


yes i think i could add the switch...not now sorry i am really busy.

but when i do i'll let you know.


May the Chuck be with you.
 
rog8811

rog8811

0
Joined
Jul 24, 2007
Messages
2,749
Points
0
Quote from PM....
nikokapo's picture was very easy to understand, although it doesnt have the reverse switch, and yours does. Is there any way your could show me in Niko's drawing where the switch goes in?:

As mikeeey asked for a reversing switch in your drawing NC, I hope you don't mind me modding it.

Regards rog8811
 

Attachments

  • spirographsetupse6.jpg
    spirographsetupse6.jpg
    90.6 KB · Views: 303
mikeeey

mikeeey

0
Joined
Jun 7, 2007
Messages
1,771
Points
0
thanks rog! I am an epic noob when it comes to electronics so could you clear up what you have added here in the picture?
spirographsetupse6bx1.jpg


I take it the reversing switch has 4 places to attach the wire? and the switch will switch the circuit? In the picture it looks like there are only 2 spots for the wires, and the other 2 wires are just hanging there and you have to manual connect them.
 
rog8811

rog8811

0
Joined
Jul 24, 2007
Messages
2,749
Points
0
Hopefully I covered the connections to the switches in my PM to you, I hope it was understandable...once you get the switch give me a make/model and I will do you a schematic for wiring that specific one. The trouble is there are so many types that a symbol drawing was all I could do that works for all switches.


You are correct with your marking of the switches on the drawing.

Regards rog8811

[edit] I have added a typical switch connection diagram, I hope it helps ;)[/edit]
 

Attachments

  • switch_connections.jpg
    switch_connections.jpg
    56.7 KB · Views: 437
mikeeey

mikeeey

0
Joined
Jun 7, 2007
Messages
1,771
Points
0
rog8811 said:
Hopefully I covered the connections to the switches in my PM to you, I hope it was understandable...once you get the switch give me a make/model and I will do you a schematic for wiring that specific one. The trouble is there are so many types that a symbol drawing was all I could do that works for all switches.

You are correct with your marking of the switches on the drawing.

Regards rog8811
Click to expand...
yes i will let you know when I get all the items necessary! ill get payed again on the first of august, hopefully then i can get everything.
 
mikeeey

mikeeey

0
Joined
Jun 7, 2007
Messages
1,771
Points
0
Can someone tell me If i have made this graph right? I have added a 3rd motor. This is without the reversing switch. If this is correct then I will make an image of 3 motors and a reversing switch.
spirographwith3rdmotorod7.png
 
mikeeey

mikeeey

0
Joined
Jun 7, 2007
Messages
1,771
Points
0
And if my above picture is correct then here it is with the reverse switch. Is this correct?
[highlight]EDITED:[/highlight]
spirographwith3rdmotorrrz2.png
 
rog8811

rog8811

0
Joined
Jul 24, 2007
Messages
2,749
Points
0
If you compare it again to my drawing you will see that you have missed out part of the reversing switch.
There should be another terminal below the row of three to the left of the switch, it will be connected to the top terminal, (light green wire).

The wiring to the 3rd motor is correct ;)


Just noticed this comment.....
I take it the reversing switch has 4 places to attach the wire? and the switch will switch the circuit? In the picture it looks like there are only 2 spots for the wires, and the other 2 wires are just hanging there and you have to manual connect them.
Click to expand...

As explained in my PM the reversing switch is like 2 switches side by side, operated by the same button/lever.  Each half of the switch has 3 contacts..... I have tried another drawing to see if it helps..... :-/  The purple lines are the the bits inside the switch which moves from one contact to the other when you move the lever, they carry the power from one side of the switch to the other.....

.........I have got to say I am running out of ways to explain this, hopefully when you get the parts it will all become clearer



Regards rog8811
 

Attachments

  • switches02_001.jpg
    switches02_001.jpg
    95 KB · Views: 235
You must log in or register to reply here.




Top