Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

O-like 200mW Green transformable is mod hop

Seoul_lasers

Seoul_lasers

0
Joined
Jul 4, 2008
Messages
2,499
Points
113
Hmm about 2 weeks ago I received a package from O-like in it were a 150mW Blu-ry pen and a 200mW transformable Greenie.

I used it 2x. I used the correct duty cycle and it seems like the optics are faulty. I have a laser beam being emitted off centre and it seem the laser is mode hopping. I get a tight beam and then it splits into a double dot (more like an 8) then it shifts back to centre.

Wow. $165 for this ?

Disappointed. It does burn, but I question the optics on this pointer. It sucks.
 





Eudaimonium

Eudaimonium

0
Joined
Feb 5, 2008
Messages
6,252
Points
83
Mode hopping is not related to optics, it is an issue of main ND:YVO and KTP crystal assembly.

A bit misaligned, or a bit underpowered or anyhow not perfect crystal mounting will result in mode hopping.
Which should not happen with O-like's products....
 
Seoul_lasers

Seoul_lasers

0
Joined
Jul 4, 2008
Messages
2,499
Points
113
actually to be more clear it seemed like there were 2 problems. One mode hopping 2 dots forming and the other is the patterning. This is most certainly optics. The main unfocussed beam is clear of patterning.
 
Eudaimonium

Eudaimonium

0
Joined
Feb 5, 2008
Messages
6,252
Points
83
Sorry, don't know how to help ya.

Keep it at room temperature, use freshly charged batteries, don't let it overheat, let it properly warm up.

Not much else you can do about it. Sorry again :(
 
Traveller

Traveller

0
Joined
Dec 21, 2008
Messages
1,223
Points
0
Seoul_lasers said:
...I have a laser beam being emitted off centre and it seem the laser is mode hopping. I get a tight beam and then it splits into a double dot (more like an 8) then it shifts back to centre...
Click to expand...
Write to Susie, explain the situation and I am sure she will replace the unit. YES, it's a pain to have to ship things back & forth, but for that price, I would make the effort.
 
Seoul_lasers

Seoul_lasers

0
Joined
Jul 4, 2008
Messages
2,499
Points
113
this is rather strange, I think the dot problem is the battery. I just tried a RCR123A cell (4.2v) and it works flawlessly. Dot stays in a circle and doesn't move into the 8 pattern.

You know I think it might just be the current of the larger cell causing the problem!
 
Traveller

Traveller

0
Joined
Dec 21, 2008
Messages
1,223
Points
0
Seoul_lasers said:
...I think the dot problem is the battery. I just tried a RCR123A cell (4.2v) and it works flawlessly ... I think it might just be the current of the larger cell...
Click to expand...
Larger cell? What cell (type & voltage) would that be, exactly?

I've had bad batteries which couldn't supply enough power in the past but maybe in your case it's the opposite? Sorry, I have no electronics background, but I think that most of the drivers used are linear and not of the level (of quality & complexity) used by our own DIYers to power their 405 & 660 lasers... :-/
 
Eudaimonium

Eudaimonium

0
Joined
Feb 5, 2008
Messages
6,252
Points
83
The problem is, that when a Crytal set is made for exact power, it will behave abnormally when pushed to higher, or under powered.

In the case of 18650, the driver maybe acting differently then with CR123, so it will supply more or less current than needed.

Basically all Nd:YVO and KTP crystals are made with some tolerance and usually this tolerance is within usage limits.
However such problems do happen.

If you ask Susie nicely, she will replace it surely.

They have the best customer service on this side of Venus.
 
You must log in or register to reply here.




Top