Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Power Estimation

Dvorhagen

Dvorhagen

0
Joined
Feb 17, 2010
Messages
82
Points
8
Heya, folks--
I'm trying to figure out an as-reliable-as-possible method for estimating the milli-wattage of a laser without a meter. I eventually intend to build one (though from what I've been reading, homebuilt power meters tend to be quite inaccurate), but in the meantime, I wonder if there are perhaps some rules of thumb or benchmarks that could give me at least a very general indication of my laser's power output.

Has anyone developed a metric based on a laser's ability to burn different materials, for instance? Or an apparent brightness comparison, as a function of its wavelength?
 





RA_pierce

RA_pierce

0
Joined
Sep 16, 2007
Messages
3,658
Points
113
Dvorhagen said:
Heya, folks--
I'm trying to figure out an as-reliable-as-possible method for estimating the milli-wattage of a laser without a meter. I eventually intend to build one (though from what I've been reading, homebuilt power meters tend to be quite inaccurate), but in the meantime, I wonder if there are perhaps some rules of thumb or benchmarks that could give me at least a very general indication of my laser's power output.

Has anyone developed a metric based on a laser's ability to burn different materials, for instance? Or an apparent brightness comparison, as a function of its wavelength?
Click to expand...

You can NOT measure a laser's power accurately with anything other than a calibrated LPM.

You can estimate within ~10% using the current your little diode is run at, but efficiency from diode to diode varies. The lens is also a contributing factor to total output power.

If you want a cheap power meter, look for Lasersbee's sales threads (in the pro shop section). He is selling 200mW meters for ~$50.
 
Dvorhagen

Dvorhagen

0
Joined
Feb 17, 2010
Messages
82
Points
8
Actually, I didn't think you'd be able to get as accurate as 10%, just doing the math. I figured the driver circuit and LD would be too lossy to get a good estimation that way. I'm going to look into building/buying a laser meter once my bank account recovers from this latest laser-splurge :)
 
Greenmechanic

Greenmechanic

0
Joined
Aug 28, 2009
Messages
1,071
Points
0
Dvorhagen,
I can give you (very) ballpark figures according to your lasers burning abilities.
What wavelength is your diode?
650nm?
532nm?
405nm?
 
RA_pierce

RA_pierce

0
Joined
Sep 16, 2007
Messages
3,658
Points
113
Dvorhagen said:
Actually, I didn't think you'd be able to get as accurate as 10%, just doing the math. I figured the driver circuit and LD would be too lossy to get a good estimation that way. I'm going to look into building/buying a laser meter once my bank account recovers from this latest laser-splurge :)
Click to expand...

That's if you're calculating current draw from batteries.
If you calculate current across the diode, you can get a much more accurate guesstimate.

Compare your diode to this:
http://hacylon.case.edu/laser/diode_blu_roundup.PNG

~110mW at 120mA with acrylic lens is typical for a PHR.

From your signature, I am assuming your diode is a PHR driven at 125mA.
 
Dvorhagen

Dvorhagen

0
Joined
Feb 17, 2010
Messages
82
Points
8
Is it safe to take a mA reading across the cap/diode (which I have very closely connected)? I notice the diode dims when I try, and I'm afraid of accidentally shorting the cap through the LD...
 
lasersbee

lasersbee

0
Joined
Sep 20, 2008
Messages
17,622
Points
113
NO..... You CAN NOT take Current readings ACROSS the diode...

What you have done is create a high amperage shunt/short across your
LD that could possibly damage your Driver or even the LD with a surge as
you remove that meter shunt...

Take your reading in series with your batteries... The LD driver only uses
a minimal amount of current and you will still get good readings of the
current the LD is driven to...

Jerry
 
Last edited:
photonaholic

photonaholic

0
Joined
Oct 24, 2009
Messages
2,738
Points
63
Multimeter 101........

Gee I wonder how many amps this here outlet on my wall is putting out??

So hmm, I will set my meter as high as it can go and stick these here probes in that there outlet...

Wow smoke just came out of my meter and the breaker just tripped, what did I do wrong???

To measure current, you MUST connect in a series with your load, NOT parallel.
 
photonaholic

photonaholic

0
Joined
Oct 24, 2009
Messages
2,738
Points
63
I just got a PM from a member, so here is the basic hook up.

It is highly recommended to use a test load rather than your diode, but this should get the point across.

series.gif
 
You must log in or register to reply here.




Top