Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Homemade CO2 laser

Things

0
Joined
May 1, 2007
Messages
7,517
Points
0
A 150W tube would be great in my machine, ignoring the fact it'd hang 2 metres out the side and I'd have to replace all the optics ... one day :D
 





HDF49

0
Joined
May 21, 2013
Messages
50
Points
8
What kind of bore is that 80 watt tube you're sorting me out with Dave? Just wondering how the current area ratio shapes up to my 11mm bore.
 

Spooky

0
Joined
Jun 1, 2013
Messages
261
Points
0
Probably 12 to 15 mm, hard to tell and no way to measure it.

1.jpg


2.jpg


3.jpg


4.jpg


5.jpg


6.jpg


Just tried the tube and measured it, it's pumping 69-72 watts effective.

cheers

Dave
 
Joined
Jan 14, 2009
Messages
1,452
Points
83
Nice Work :D ,

When I got my Co2 from a UK company , they delivered it themselves in there own van as UK postage would just break the 60 W tube :p

Edit - Just saw the pictures , My tube was from HPC lasers :D
 
Last edited:

HDF49

0
Joined
May 21, 2013
Messages
50
Points
8
That all looks absolutely great Dave, the high voltage from that PSU should certainly help get over worries about my vacuum pump not being up to scratch. Would me picking it up or you dropping it off be easier for you?
 

Spooky

0
Joined
Jun 1, 2013
Messages
261
Points
0
Nice Work :D ,

When I got my Co2 from a UK company , they delivered it themselves in there own van as UK postage would just break the 60 W tube :p

Edit - Just saw the pictures , My tube was from HPC lasers :D

Chris at HPC is an old friend :) I've had quite a few of his machines so far without any problem. He's a clever chap too, there isn't very much he cannot fix when the need arises.

I don't mind dropping it off Henry, I'm in Bath next week on two days :0

cheers

Dave
 

HDF49

0
Joined
May 21, 2013
Messages
50
Points
8
That would be great thanks Dave, what days and at what kind of time? I'm back doing my A levels so may have to arrange it so you meet with my dad but I do have a bit of spare time.
 
Last edited:
Joined
Aug 14, 2013
Messages
2,655
Points
63
Was digging about today and found a Clarke CL300 lathe that had never been used along with matching milling machine.

Those are a pretty nice lathe once the jibs are tightened up and everything straightened out.
I have prettymuch the exact same thing. Too bad though it's not a little bigger. The mills however are another story. Loose parts, noisy geartrain, etc. Have you powered either up?
 

HDF49

0
Joined
May 21, 2013
Messages
50
Points
8
What kind of machining do you do? I've been using my dad's colchester student lathe and dawe westbury mill for all my work, it's very nice to have large machines working well within their comfort zone, it made machining the mirror mounts a breeze.
 
Joined
Aug 14, 2013
Messages
2,655
Points
63
I've made a diode press, battery tab welder electrodes, other hand tools, heat sink customization, etc. Right now I'm making an entire host from scratch for the I "C" Red Battle Royale contest. It would be nice
though to have something larger like that colchester, South Bend, or a Bridgeport. :whistle:
 

Spooky

0
Joined
Jun 1, 2013
Messages
261
Points
0
Those are a pretty nice lathe once the jibs are tightened up and everything straightened out.
I have prettymuch the exact same thing. Too bad though it's not a little bigger. The mills however are another story. Loose parts, noisy geartrain, etc. Have you powered either up?

It's the bigger one of the two mills, I have all the collet chucks (ER20's) and extra stuff, both power up fine (they are variable speed) I just never got round to using them. I did have a pretty extensive machine shop at one point but eventually sold that side of the business off to concentrate on laser cutting.

That would be great thanks Dave, what days and at what kind of time?

I'm at Jennor in Bristol Tuesday and Thursday and will be going via Bath :) between 5pm ish and 8pm ish I would think.

is that with the shipping? or just the cost of the tube alone?

It's the length Truss, weight isn't a problem, but parcels that length on my courier cost £523.66 to ship to the East Coast from here. If the tube could be sawn in half it would cost under £75 to send. I can get an 120 watt EFR or RECI shipped here from China for just under 2/3rds of that! That aside, I can imagine the US customs service thinking it's some kind of component for a hand held laser cannon and hanging up every thing I send to the US afterwards.

cheers

Dave
 

HDF49

0
Joined
May 21, 2013
Messages
50
Points
8
I should be able to manage that, where abouts in Bristol is that? I've googled it and can't find anything
 

Spooky

0
Joined
Jun 1, 2013
Messages
261
Points
0
Keynsham at the Avon Plywood offices :) so I have to go via Bath from here anyhows :)

Sometimes my job is mind numbingly boring 10,000 of these, 50,000 of those etc etc :(

cheers

Dave
 

HDF49

0
Joined
May 21, 2013
Messages
50
Points
8
Ah that's good, I'm just outside of Bath on the south side, would it be easier for us to meet somewhere on your route or do you want to drop the stuff off at mine? What's the plywood for? Do you ever get any one off jobs or is it more big contracts?
 

Spooky

0
Joined
Jun 1, 2013
Messages
261
Points
0
I do quite a bit of one off stuff to pass the time when the contract orders get tedious :) The Ply is for making markers for wargames for the Warhammer manufacturer over in the US. Sometimes I'll make stuff like doll houses or ornate boxes just to see something different for a few hours :) I do contract work for individuals as well when time permits.

Will be easier to drop the tube at yours, it's 5.5 feet long and fragile to be transporting around :)

cheers

Dave
 




Top