Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Spirograph, the 765th.....

A

anselm

0
Joined
Nov 22, 2010
Messages
2,448
Points
0
Hello there, here is my spirograph V2.
-3 motors, a poti each and two of them have reversible direction
-fixed green with LM1117 driver
-runs off a single LiIon
gedc0899.jpg

It looks like frickin mess, but I kinda do like it.
gedc0904.jpg

Hope I didn't bore you guys too much.:na:

OK, so here's a video, trying to catch some of the best effects:
 
Last edited:





That's a spiro direct from CNI, correct?

J/k, I love seeing people recycle stuff as I do it too.
 
Pretty cool set up you have made there I realy like how you have recycled everything right down to the insulated connection points, +2 for a job well done, lets see some beam shots now ;)
 
Last edited:
Yes, I have yet to build one, and absolutely LOVE seeing the output these produce, so how about it? Let's get some action shots!
 
I can't think of the schematic for a reversible direction for a motor... mind elaborating?
 
Wolfman29 said:
I can't think of the schematic for a reversible direction for a motor... mind elaborating?
Click to expand...
IIRC some use a DPDT switch- middle is off and two directions right and left.

+1 if you tell where you harvested those pots. i want 4 motors and the ability to go slowly from dead stop to fast.

Can I 'knife edge' lasers of different nms? as long as they were a little tight together and fit on the mirrors 3 colors would be nice imo.:yh:
GOOD[ but sloppy (like me) ]

HAK
 
Wolfman29 said:
I can't think of the schematic for a reversible direction for a motor... mind elaborating?
Click to expand...
reverse.gif


hakzaw1 said:
+1 if you tell where you harvested those pots. i want 4 motors and the ability to go slowly from dead stop to fast.

Can I 'knife edge' lasers of different nms? as long as they were a little tight together and fit on the mirrors 3 colors would be nice imo.:yh:
Click to expand...
Sorry to disappoint you, those are the volume knobs from the CD-ROM drive.:D
And they are "tuned" with a resistor in parallel, but the control is horrible.:D
One has the motor stopped for all but the last 1/10th of the range,
another one only goes from "slow" to "somewhat faster" over the whole range,
only one actually goes from stop to fast in a somewhat linear manner.
I'll either have to retrim those other two pots, or maybe let the pots
drive transistors, or maybe go buy some proper potentiometers in the first place, or....

I think I could maybe dichro in a red beam there without too much trouble, using the PHR sled mirror.
Good idea, hmmmmm....

Flaminpyro said:
... lets see some beam shots now ;)
Click to expand...
jakeGT said:
... Let's get some action shots!
Click to expand...
I thought people here would be familiar with 3 motor spiro images, there
are a couple videos on the forum after all, but yeah, let me try and get
a good video.
 
Two choices for me-(my soldering and building skillz suck) either a ready-made or kit DC motor controller. Neither is cheap and I need four. Somebody said the ceramic rheostats can be used but IDK . Anyone wantig free pots or rheos in return for knowledge check the pics in my albums at my profile page . I have about 200 from a lot eekbay buy.

meawhile I found an easy solution-- i am going to 'cheat' I took apart 2 small red DJ laser spiros w/speed & direction controls- and music reactive mics- swapping out the red for Br and Green and combining to two to make one 4 motor, paid less than 30$ for both-as-is for repairs etc.

pics as the 'build' progresses-

I also sell at cheap prices 3vdc quaility motors with FS mirrors already attached.
PM for details. sizes med. small and even smaller-
 
Last edited:
As you can see, I should mount a bigger mirror on the last motor.:angel:
 
Last edited:
Very nice and fun anselm, congratulations :beer:

Appears mounted on the carcass of a hard drive, but obviously this looks bigger :D
 
You must log in or register to reply here.


Back
Top