Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Red DIY DVD laser burner.

Gazoo

Gazoo

0
Joined
Jun 9, 2007
Messages
3,206
Points
38
Dark_Horse said:
Gazoo, If I used an open-can LD, like from the DVR115, in place of the GB LD, would I be OK with the 350ma that my Dorcy is putting out without resistors, then I would just need to add a capicitor to the LD, and I should have a reliable-long-lived that can burn like the GB LD, maybe a little better?
BTW, Where do I buy the Merideth module, I would like a little better optics?
Thank you all,
Dark Horse
Click to expand...

I think you would be fine with an open can running directly off of the circuit. Maybe Kenom can confirm this but I don't think a capacitor is necessary because the Dorcy circuit already has one on there.

The meredith modules do have some drawbacks. Sometimes when turning the focusing ring the diode turns with it. Jay noticed that the adapter was a bit too long in one he received so he had to trim the adapter down so it would focus for distance. The the lenses are better than the aixiz, whether or not you get a glass or acrylic lens. The acrylic seems to burn a bit better especially when lighting matches at a distance, however the glass lens lets more light through so the output is increases, but the beam diameter is larger. As with the aixiz, there is some wiggle in the threads. It would be nice to find modules that don't have this problem. By making finer threads the problem would be solved. Anyway, here is the link:

http://www.mi-lasers.com/cgi-bin/shopper.cgi?search=action&keywords=diode_optics

If you order one make sure to get the 5.6mm to 9mm adapter.
 





roSSco

roSSco

0
Joined
Dec 5, 2007
Messages
649
Points
18
I'm running an open can straight off of the Dorcy circuit @~320mA w/o any problems. ;) It works great! I have been using it for about a month with many runs > 1 minute.
 
TheMonk

TheMonk

0
Joined
Aug 29, 2007
Messages
750
Points
0
I'm running an open can too using the Dorcy circuits for over 3 months now. [smiley=wink.gif] Using Panasonic Lithium Primary I can get 340mA, run time ~2 minutes.
 
Dark_Horse

Dark_Horse

0
Joined
Dec 26, 2007
Messages
682
Points
28
Kenom,
Thanks for reposting the picture of the circuit, I am not very familiar with Suface-mount componets, can you verify that one is a capicitor, and so I do not need to add one?
Thank you to everyone else confirming that an open-can can run directly from the stock circuit, looks like I will be doing some experiment with diferent LD's , hopefully I will get to try the "Phasor LD" next, if the GB goes through;)
Dark Horse
 
D

danq

0
Joined
Sep 18, 2007
Messages
835
Points
18
Dark_Horse said:
Kenom,
Thanks for reposting the picture of the circuit, I am not very familiar with Suface-mount componets, can you verify that one is a capicitor, and so I do not need to add one?
Click to expand...
Kenom said:
yeah it has 2 capacitors on it.
Click to expand...
Yes, but are they across the laser diode? They don't look like high-value capacitors from the photo...
 
Gazoo

Gazoo

0
Joined
Jun 9, 2007
Messages
3,206
Points
38
tone1132 said:
How do you know what pins are pos & neg on the diode??
Click to expand...

There is a sticky posted at the fop of this section of the forum called Group Buy Diode Pin-outs !
 
T

toked323

0
Joined
Sep 1, 2007
Messages
1,591
Points
0
hey kenom how hard is it to get the driver out of the dorcy? i was thinking to rreplace the surface mount resistor with a higher rating resistor so no need for it on the diode
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
it's pretty easy to remvoe. Just push another battery in there as well as the existing one and keep applying steady soft pressure.
 
Abray

Abray

0
Joined
Nov 18, 2007
Messages
933
Points
0
hey,

I am thinking about starting one of these projects soon, as I have a spare 50 dollars(or whatever will be left after buying a CR123 battery for my Galileo). I have wire and a switch and a capacitor (47uF 10V I think, is that large enough?). I also have an AixiZ module to put a diode into. the only thing (I think) I need would be a power source, maybe a pot (what rating?), a resistor, and the actual diode itself!

I can figure out or look up what resistor size to use, but what about all those other components. Is my capacitor large enough? What pot would I need, and what kind of power source would I want? also, is an AixiZ module enough to heatsink it? and I won't be over driving this diode, only keeping it at a constant 150 or 200 mW.
 
T

tone1132

0
Joined
Jan 1, 2008
Messages
276
Points
0
did you cut the bottom off the laser housing? and is there any resistors or anything protecting the diode?? im pretty new here, thanx
 
T

tone1132

0
Joined
Jan 1, 2008
Messages
276
Points
0
well i watched the video. i electricly isolated the cooections, i cut into the aluminum, is that ok? i had a good connection when i soldered it and put it together it was completely dim and got pretty warm. whats the deal??
 
Kenom

Kenom

0
Joined
May 4, 2007
Messages
5,629
Points
63
if it was dim then you've fried the diode. it's possible that you killed it by esd or shorting the pins together. I'm putting together a more complete walkthrough video.
 
You must log in or register to reply here.




Top