Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Pen style blu-ray tutorial






VW

0
Joined
Mar 1, 2008
Messages
577
Points
0
I will be reading through this in more detail for sure. Good stuff...
 
Joined
Apr 1, 2008
Messages
3,924
Points
0
Mitch took my trashed WL CLASSIC CASING & modded it just like his tutorial, & it worked great. His craftsmanship is excellent & his turnaround time quick ;) One improvement I could see him making though, & MITCH, I meant to PM you about this but I spaced out on it & forgot. The small pcs. of Aluminum foil that you used to make good electrical contact between the Aixiz Module & the host body could be replaced by sticky backed copper foil. You can get it from DX in several different mm widths. It comes on a roll like scotch-tape. Just peel off how much you need & wrap it around, or stick it on the module wherever you need it. Since it has a sticky back, it stays in place while re-assembling the laser ;) Also since it's made of all copper, it conducts electricity or a ground very well, & does double duty as a mini-heat-sink of sorts too. Thanks for the fine job that you did on it, & that assembly has since gone on to do duty in another laser I'm working on. GREAT JOB,MOD, & TUTORIAL ;) phoenix77/rob :cool:
 
Joined
Feb 29, 2008
Messages
2,344
Points
0
i have just noticed phoenix77 - you must have the best post/rep ratio :)
 
Joined
Nov 24, 2007
Messages
2,735
Points
0
Hi! Nice tut! I just got a little confused. Wouldn't it be simpler to just connect the case pin to the + pin on the 803T and not have to solder the + wire to the case pin on the driver? That would be a lot simpler. Also, how do you know where the input and output on the switch are. Sorry, i have never worked with pen hosts >.<
 
Joined
May 2, 2008
Messages
2,025
Points
63
Spyderz20x6 said:
Hi! Nice tut! I just got a little confused. Wouldn't it be simpler to just connect the case pin to the + pin on the 803T and not have to solder the + wire to the case pin on the driver? That would be a lot simpler. Also, how do you know where the input and output on the switch are. Sorry, i have never worked with pen hosts >.<
The input and output of the switch don't matter because there's just 2 two pins, one on each side, and isn't polarized. I don't know about flex, but with rkcstr you CANNOT solder the case pin to the +, it will die instantly (trust me, i know lol) however you can solder it to the - (go figure :-/ ).
 
Joined
Nov 24, 2007
Messages
2,735
Points
0
HumanSymphony said:
[quote author=Spyderz20x6 link=1214277097/20#36 date=1224712872]Hi! Nice tut! I just got a little confused. Wouldn't it be simpler to just connect the case pin to the + pin on the 803T and not have to solder the + wire to the case pin on the driver? That would be a lot simpler. Also, how do you know where the input and output on the switch are. Sorry, i have never worked with pen hosts >.<
The input and output of the switch don't matter because there's just 2 two pins, one on each side, and isn't polarized. I don't know about flex, but with rkcstr you CANNOT solder the case pin to the +, it will die instantly (trust me, i know lol) however you can solder it to the - (go figure :-/ ).[/quote]
Oh... i guess the Rckstr is case negative. That is odd...
I don't get it though, because it stil would be the same connection. What if i just solder the case pin and the - pin together on the 803T, and then i just leave the - terminal on the Rckstr driver untouched. Then i would just put the batteries in the positive side :D
 
Joined
Oct 11, 2008
Messages
134
Points
0
WOW thank you +1
i just completed a PHR built in one of Jayrob's chrome hosts but am awaiting batteries.
Its running at 80mah
thanks again great and clear tutorial
 




Top